|
| DMac |
|
||
Age: 38 Posts: 1372 Joined: 7th Nov 2004 Ride: Lancer Coupe Location: Southeastern suburbs, Melbourne |
Hey guys, i wanna put some Leds in the car for some effects. Yeah yeah say whatever you want. But anyway i was wondering about power supply. I was thinking of running a thin power cable from the battery to a little distribution block located somewhere. Then from this distribution block i would run the leds off it to the desired location. Anyway i was wondering would i need a resistor for each LED or could i just have one 560ohm resistor before the power get to the distribution block(home made of course).
Cheers fellas |
||
| Top | |
||
| Marmo aka GRNGOB |
|
|||
|
the resistance of the resister would depened on how many leds u have so it mightant be a 560ohm resister. but imo best way to do it would do a resister on each one because that way u can always add more leds and stuff like that.
i think it would look really good if done right. what type of look are u goign for? like a spot light or a glow type of thigs.
_________________ Spooling soon... |
|||
| Top | |
|||
| Marmo aka GRNGOB |
|
|||
|
sorry i was thinking of wireing it in series yeh just do one resister in the block and wire them up in parael
_________________ Spooling soon... |
|||
| Top | |
|||
| voids |
|
|||
|
check out my courtesy lights in my gallery
_________________ '96 DF II LTD 6cy |
|||
| Top | |
|||
| snap0964 |
|
|||
|
The DMac wrote: I was thinking of running a thin power cable from the battery to a little distribution block located somewhere. Then from this distribution block i would run the leds off it to the desired location. If your LEDS will be inside, you could run your power off the interior fusebox - typical LEDS only draw around 120 milliwatts.The DMac wrote: Anyway i was wondering would i need a resistor for each LED or could i just have one 560ohm resistor before the power get to the distribution block(home made of course). You can get away with the one, but you need to increase it's power rating, and this will be dependant on the number of LEDs.Marmo aka GRNGOB wrote: sorry i was thinking of wireing it in series yeh just do one resister in the block and wire them up in parael By my calculations, you should be able to put 2 LED's in parallel, and then in series with 1 560 ohm ¼watt resistor. If you need 4 LEDs in a row, you can put them in series with each other, without a resistor - each drops 3.4 v, so 4 x 3.4 = 13.6v, I've tested this, and works fine. You can also run 3 LEDs in series without a resistor on 12v, I've tested this also, but the life of the LEDs may be shortened by the larger operating voltage across each LED. So you do have a few options . . . .
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| DMac |
|
||
Age: 38 Posts: 1372 Joined: 7th Nov 2004 Ride: Lancer Coupe Location: Southeastern suburbs, Melbourne |
thanks guys
|
||
| Top | |
||
| snap0964 |
|
|||
|
For those with a little electrical knowledge - here's a handy webpage to calculate components and ratings for different LED configurations: http://www.besthongkong.com/clrc.htm
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| Laximah |
|
|||
|
voids wrote: check out my courtesy lights in my gallery
hey voids, thats a pretty neat idea!
_________________
|
|||
| Top | |
|||
| voids |
|
|||
|
Laximah wrote: voids wrote: check out my courtesy lights in my gallery hey voids, thats a pretty neat idea! cheap and easy too. they are easy to hide with minimal visibility but heaps of light output. i replaced the light above the ignision switch with a LED also. even put a few on my motorbike while i was at it.
_________________ '96 DF II LTD 6cy |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 38 guests |
