|
Mitch_ |
|
|||
Posts: 6168 Joined: 5th Nov 2004 |
{USERNAME} wrote: underneath where the legs are that hinge on all i did to fix mine (ef fairmont) was to melt part of the legs n melt a lil of the plastic to make a heap more resisitance to stop the cup holder arms falling down n drinks going everywhere... coke/ants and cars dont mix... cost nothing to modify and now the drink holder works as it should do...was a 15 min job...
hahaha that works sweeet! havnt tested it out with drinks yet...but its a hell of a lot harder to push it down
_________________ |
|||
Top | |
spannerhead |
|
||||||
|
Heres a 5 cent solution to the cupholder dilemma...Its an extension of 4.9 ef's bulldog clip solution, but a bit cleaner. Ive got tons of these paperclip things on my desk. Works a treat....very sturdy.
Available where all good stationary is stolen!
_________________ Thorpy says single wipers are Fully SIK!
|
||||||
Top | |
Froudey |
|
||
|
Oh My GOD!!! i know what a problem!
If you don't know i am being sarcastic!! simple don't go to maccas as often!! don't know why cars have these all the posh import cars and proper sports cars don't have them why cause you got to concentrate on the road. go to clints and buy the 3.50 plastic thing that sites in the grove of the window.
_________________ R.I.P Tobias my son. |
||
Top | |
EBII92 |
|
|||
Age: 39 Posts: 637 Joined: 25th Nov 2004 Ride: Toyota Surf, EF Fairmont Location: Melbourne, Northern Suburbs |
why spend 3.50 on a cup holder from clints, when the cup holder is already in place. i could go to MACCAS and buy a thinkshake and fries for 3.50
|
|||
Top | |
shoey50 |
|
||
|
what do people think of the little actuator idea? any good any idea what would suit and where i could get one
|
||
Top | |
fordfreak ef |
|
|||
|
{USERNAME} wrote: Hey fordfreak....you got any pics of what youve done to the menace cupholder?. Sounds like a good fix that other people could do too! posting pics is harder than the job itself lol all u do is melt a little part of the legs underneath with a soldering iron n shape the soft plastic..wait for it to cool n harden in place n voila! "bobs your aunty!!" install back in n marvel at the ease of whhich my can of coke sits in the holder.. even around corners!!
|
|||
Top | |
fordfreak ef |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: underneath where the legs are that hinge on all i did to fix mine (ef fairmont) was to melt part of the legs n melt a lil of the plastic to make a heap more resisitance to stop the cup holder arms falling down n drinks going everywhere... coke/ants and cars dont mix... cost nothing to modify and now the drink holder works as it should do...was a 15 min job... hahaha that works sweeet! havnt tested it out with drinks yet...but its a hell of a lot harder to push it down |
|||
Top | |
EACRUISER |
|
|||
|
The question of the actuator, i woul say hook up a couple of central locking actuators and attach them to the bottom of the arms. then hook them into a rocker switch. one way up, one way down.
Real cheap if you pull them out of U-pull it or the like, places. |
|||
Top | |
EBGizmo |
|
|||
|
Ok, heres my attempt at solving this problem.
In a nutshell, i've just increased the pressure that the little black locating lugs push against the "cam" on the moving part of the holder. I did this with two short pull springs and two short bits of wire made of the same metal as the springs (straightened out spring wire) The only modifications done to the cup holder itself is 2 holes melted into the locating lugs, and 2 holes at the back of the black plastic (see pics) I don't think I need to go into details, as the pics pretty much explain all. On each side, the wire is attached to the hole melted in the lug (Holder_1.jpg). The other end of the wire has a hook, and is connected to the pull spring, which is hooked around the hole melted in the back of the plastic (Holder_3.jpg). The end result is a much more positive locking feel, but everything appears the same once assembled. I've used a pretty strong pair of springs, I had to cut them to the correct length to get the right amount of tension on the lugs. Experiment to get a result you're happy with. Also, don't forget to smear a bit of grease on the lugs and cam to reduce wear.
_________________ EF II Sedan
|
|||
Top | |
phongus |
|
|||
|
hmmmmm havent had that problem in my EL yet....since i dun allow anyone to drink or eat in the car.......the EA how ever never came with one....disasterous times. but the spring idea was good EBGizmo but i might give the actuator idea a go.
phong =P~
_________________ phongus = Post whore 2006 |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 11 guests |