|
| FLYING XR8 |
|
|||
|
I tapped the air bag screws in my AU loose with a woodworking chisel.
I tapped around the edges until they were loose enough to undo by hand. Before I put them back I cut a slot in the top with a Hacksaw and screwed them in with a Screwdriver. Dodgy but it worked. |
|||
| Top | |
|||
| Timmeh |
|
||
|
Screamer wrote: thanks i'll try d**k smith's then, if they don't have them the i'll try FTG or i might drill it out.
Its not a Torx bit so you wont find it there. FTG have them thats where I bought mine from. If you read my first post i said the torx bit has 6 points on it where as the Au airbag bolt has 5, so a torx bit wont fit. Here the thread I did a while ago on the bolt for AU airbags. http://www.fordmods.com/forums/viewtopi ... light=torx Try the search function next time. I found that thread easy with search. |
||
| Top | |
||
| macca13 |
|
||
|
Most tool places stock the anti-tamper torx bits thats where i got my set anyway.
|
||
| Top | |
||
| madmax |
|
|||
|
Timmeh wrote: Screamer wrote: thanks i'll try d**k smith's then, if they don't have them the i'll try FTG or i might drill it out. Its not a Torx bit so you wont find it there. FTG have them thats where I bought mine from. If you read my first post i said the torx bit has 6 points on it where as the Au airbag bolt has 5, so a torx bit wont fit. Here the thread I did a while ago on the bolt for AU airbags. http://www.fordmods.com/forums/viewtopi ... light=torx Try the search function next time. I found that thread easy with search. They are still a torx bit just not a 6 lobe one, see my post. People need to ask for the correct thing and its not going to be easy as they are not readily available.
_________________
|
|||
| Top | |
|||
| EFfalconsrule |
|
||
|
Mine had a anti tamper torx bit not one of them 5 point ones. Must be different.
_________________ Stage 1 stereo install done. Pics in audio section. |
||
| Top | |
||
| Mechan1k |
|
||
|
I got the little ones out behind the steering wheel with an Allen key ... was fiddly ... but i got it ... the looked like the TORX bit screws to.
Used a T50 for the centre nut on the steering wheel ... but seeing as you are changing the burrons only ... you won't need it.
_________________ 04 Territory TX AWD - Winter White - optioned up |
||
| Top | |
||
| iam death |
|
|||
|
i took my el too the ford dealership in port macquarie.the head mechanic said he had never put an au wheel on an el,i told him it was a straight swap so he took my word and did it.took him 5 mins,cost me zip...
_________________ 'WALKER f**k MY WIFE AND ALL I GOT WAS THIS s**t SIGGIE' |
|||
| Top | |
|||
| qwerty68 |
|
|||
|
what is FTG auto salvage
is it like web site ? cos i need one of these screw drivers
_________________ Lukey Extractors 2.5" Exhaust 3.23:1 Diff 17" BA XR8 Alloys |
|||
| Top | |
|||
| madmax |
|
|||
|
qwerty68 wrote: what is FTG auto salvage
is it like web site ? cos i need one of these screw drivers Check the top of the forums page. They are a site sponsor
_________________
|
|||
| Top | |
|||
| Nicko |
|
|||
|
|
|||
| Top | |
|||
| GlennBA |
|
|||
|
screamer if you were in brissy i'd let you borrow mine. It cost me like $30 from FTG.
|
|||
| Top | |
|||
| AU_Steve |
|
||
|
Just replaced my steering wheel in the AU. A bit fiddly but if you have an old flat screwdriver that fits into the security bolt, cut a slot in the middle of it so that it fits over the pin in the middle ( the screwdriver blade sort of looks like a snakes tongue). It comes out quite easy, at least mine did.
Cheers AU_Steve |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 78 guests |
