|
| richie |
|
||
|
My daughter just bought AUIII I6 03/2002 on factory gas. I am about to do service - however there is I believe, a filter at the convertor. What is involved in changing this or is it a no go item?
Is it worth changing leads & coil - done 200,000k? What's the story with the Ford Motor oil for gas - should I use it? Change HEGO? I am told the OEM one is around $300. Apart from above & oil filter, air cleaner, spark plugs, coolant flush, thermostst change, brake fluid flush, auto trans service, -anything else? Richie.
_________________ 1993 ED F/mont 5.0L, Auto, Edelbrock RPM's, CompCam XE276HR, Crane Gold Race 1.7's, Edelbrock Performer, 75mm T/B, MAP, 42lb , GenIII coils, PH4000's , Twin 2.5", Thermos & underspeeds, 3.7 LSD, 2800 stall and MoTec M800, 372fwhp @ 5400rpm & 387 ft-lb @ 4400 rpm. |
||
| Top | |
||
| AU2SR |
|
|||
|
{USERNAME} wrote: My daughter just bought AUIII I6 03/2002 on factory gas. I am about to do service - however there is I believe, a filter at the convertor. What is involved in changing this or is it a no go item?
Is it worth changing leads & coil - done 200,000k? What's the story with the Ford Motor oil for gas - should I use it? Change HEGO? I am told the OEM one is around $300. Apart from above & oil filter, air cleaner, spark plugs, coolant flush, thermostst change, brake fluid flush, auto trans service, -anything else? Richie. i run magnatec by castrol do the leads and plugs there is a filter on the converter but get a gas guy to do it if it is getting bad econ change the thermostat and coolant with just inhibitor and disconnect the battery for 60 mins . hope this helps cheers
_________________ Technical Advisor AA GASKETS |
|||
| Top | |
|||
| richie |
|
||
|
{USERNAME} wrote: My daughter just bought AUIII I6 03/2002 on factory gas. I am about to do service - however there is I believe, a filter at the convertor. What is involved in changing this or is it a no go item?
Richie. Any idea about this circular wire guaze size of 50 cents filter? Richie
_________________ 1993 ED F/mont 5.0L, Auto, Edelbrock RPM's, CompCam XE276HR, Crane Gold Race 1.7's, Edelbrock Performer, 75mm T/B, MAP, 42lb , GenIII coils, PH4000's , Twin 2.5", Thermos & underspeeds, 3.7 LSD, 2800 stall and MoTec M800, 372fwhp @ 5400rpm & 387 ft-lb @ 4400 rpm. |
||
| Top | |
||
| richie |
|
||
|
Is there a manual (apart from Ford worshop) that covers AUIII factory dedicated Gas?
Richie.
_________________ 1993 ED F/mont 5.0L, Auto, Edelbrock RPM's, CompCam XE276HR, Crane Gold Race 1.7's, Edelbrock Performer, 75mm T/B, MAP, 42lb , GenIII coils, PH4000's , Twin 2.5", Thermos & underspeeds, 3.7 LSD, 2800 stall and MoTec M800, 372fwhp @ 5400rpm & 387 ft-lb @ 4400 rpm. |
||
| Top | |
||
| Mechan1k |
|
||
|
I was unaware of a filter on the converter for the factory VIialle converters ... I just replaced the converter on AUII EGAS ute ... and I didn't see one at all.
I used Shell 15W40 LPG oil ... it does the job ... I replace it every 5,000km though as I do a lot of city metro driving ... and oil is cheap insurance. For EGAS models I am pretty sure it mentions 15W40 anyway (not the 10W40 or 30 for the petrol models) I purchased a new Ford HEGO sensor on eBay for $55 ... works a charm and very easy to unbolt out of the exhaust and replace. If the vehicle is new to you ... replace the spark plugs at least. Also a clean out of the throttle body might be a good idea too ... every little bit helps. If you have a decent LPG mechanic nearby ... get them to remove and clean the idle jet ... and clean the gunk out of the solenoid plungers as well.
_________________ 04 Territory TX AWD - Winter White - optioned up |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 7 guests |
