|
Samsy |
|
|||
|
Gday, Im getting some rust repairs done around the bottom corners of my rear window in the XB. Will be cutting and welding. The guy doing the welding is concerned about welding with the LPG tank in the boot. Hes worried he might get blown up ! Should I remove the tank? Or will it be safe as long as I shut off the gas at the tap and purge the lines of anything left, and leave the tank where it is.
Cheers.
_________________ XB 351 and BA GT Last edited by Samsy on Mon Jan 14, 2008 1:21 pm, edited 4 times in total. |
|||
Top | |
Krytox |
|
|||
|
Funny, the gas is on the inside of the tank.
Enough ventilation should be fine, however, Thinking smart and worksafe are both good idea's Small/External welding, no-where near the tank I'd do without removal, but for the sake of your shed, lives, animals and property, I'd undo the 4 bolts and lines and remove it! hell if its full, He's even there to help remove!
_________________ Carefree, we may not be number one, but we're up there. |
|||
Top | |
snap0964 |
|
|||
|
Well, if it's dual fuel, and you are worried, you could delay the repairs, run the LPG tank empty, run on petrol, and LPG fill up after the repairs.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
Top | |
Samsy |
|
|||
|
No - straight gas.
_________________ XB 351 and BA GT |
|||
Top | |
phongus |
|
|||
|
{USERNAME} wrote: Well, if it's dual fuel, and you are worried, you could delay the repairs, run the LPG tank empty, run on petrol, and LPG fill up after the repairs. Was going to suggest running the tank dry... but {USERNAME} wrote: No - straight gas. just through it that idea out the window.
I would suggest removing the tank if you can to be safer. If you can syphon gas, I'd say do that... phong =P~
_________________ phongus = Post whore 2006 |
|||
Top | |
Samsy |
|
|||
|
Ok the consensus is to remove the tank, so better to be safe than lazy ! So remove the tank we shall !
Cheers fellas
_________________ XB 351 and BA GT |
|||
Top | |
twase |
|
|||
|
A full tank is less explosive than an empty one. That said, go and get the gas installation checked for leaks prior to the work.
_________________ BF Fairmont Ghia Series II update. |
|||
Top | |
Samsy |
|
|||
|
Well all the work is done. A great job too. If anyone needs rust repairs done, I can recommend Michael who did mine. No bodgy job . He plates and Migs everything, and he usually doesnt mine if you watch him work (so u can see its done right).
If u need some work done, give him a call and tell him I (Paul - Mulberry XB) gave you the number Michael Black (Blacky) Ph: 040 800 4116
_________________ XB 351 and BA GT |
|||
Top | |
AUXR8 2 |
|
|||
|
most of the repitable pannel shops in the Liverpool area that have gas related jobs they have to remove the cylinder/s part of OHS then when they put it together & can't get them going............. they call me
Joe I know late post.. |
|||
Top | |
Samsy |
|
|||
|
Hey Joe Well he was a bit nervous about it but he spoke to his old man who has been a panel beater for 30 odd years and his dad said he'd be ok to leave it in. Do a leak test on it and if all was good, then cover it with damp rags and a fire blanket. ......Did that, job was finished and Im still here ! - no bangs lol.
p.s. Must get out to you in the near future for a good tune ! Cheers.
_________________ XB 351 and BA GT |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 20 guests |