|
| redrocket |
|
||
|
mates got a vl and isnt happy wit the turbo and is goin bigger hence he is givin me his old one. stoire is wat would i need other than exhaust manifold, bov, cooler n piping, high fuel pressure reg, ecu?? would want 2 keep it under say 2 thou and aim for bout 200kw. also the turbo off vl's is a t04 yes?
|
||
| Top | |
||
| nannas_ed |
|
|||
|
dont want to ut a damper on things but i doubt you will have it installed and ready to go for under $2k. the ecu alone will cost you that much. also might want to look into a high volume fuel pump
_________________
|
|||
| Top | |
|||
| redrocket |
|
||
|
was thinkin on low boost to reach 180 200kw so was hopin ecu should b fairly right? old man works at repco 2 so i can get s**t cheap.
|
||
| Top | |
||
| twr7cx |
|
|||
|
redrocket wrote: was thinkin on low boost to reach 180 200kw so was hopin ecu should b fairly right? old man works at repco 2 so i can get s**t cheap.
You might want to tell him to get one of the intercoolers currently on special then! And tell him to get the guy in teh wrehouse to check it first, as a couple have been a bit rough in the construction. Getting a BOV should be easy for him, as most stores are stocking them now. ECU's, I've never found a supplier at work who does em. |
|||
| Top | |
|||
| redrocket |
|
||
|
i know!! this is y i need 2 know if the ecu will b fine on low boost or maybe b able 2 be reprogrammed?? makin say 180 200 kws? also does the compression need 2 b changed??
|
||
| Top | |
||
| EFFalcon |
|
|||
|
$2k for 200rwkw... not a chance.
and VL turbo's came with a T03.
_________________ FALCN6 - EF GLi Turbo, 20" Rims, Air Bag Suspension, Straight LPG, 225rwkw |
|||
| Top | |
|||
| redrocket |
|
||
|
wasnt talkin about rwkw! and would a t03 b 2 small?
|
||
| Top | |
||
| p0ly |
|
|||
|
im pretty sure ud be able to reach the 180 200 fwkw mark for less than 2000 by keeping it N/A and going for exhaust extractors intake and cam work...
_________________ <br> |
|||
| Top | |
|||
| redrocket |
|
||
|
that isnt the point!!! the point is FREE TURBO! im just woundring if it is 2 small tho? im just aiming for low boost and about 200fwkw mark nothing 2 major i dont want 2 b a horsepower hero and i dont want 2spend to much..... question is would stock comp hold up? and compression ratio??
|
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
redrocket wrote: that isnt the point!!! the point is FREE TURBO! im just woundring if it is 2 small tho? im just aiming for low boost and about 200fwkw mark nothing 2 major i dont want 2 b a horsepower hero and i dont want 2spend to much..... question is would stock comp hold up? and compression ratio??
the turbo is to small.. all you'll get is really aerly boost then above 4000rpm it will choke the engine. no chance on stock computer. compression will be fine, im going to be using 9:1 when i do my engine |
||
| Top | |
||
| EDXR8 |
|
|||
|
I think you will be fine with the stock EEC with such a low boost setup, there are quite a few people doing it. Just run a rising rate reg and a good fuel pump to richen things up under boost and maybe back the timing off a bit. A better way would be to get soemthing like a chiptorque, they do off the shelf tunes for upto 6psi I believe (more than enough for 200kw IMO) above that you want something custom tuned like a unichip or aftermarket system. As said the T3 is a bit small, but for the power you are aiming for I think it will be OK. I would run a basic manifold, you can get away nice and cheap by modifying the stock manifold. With a low boost setup you don't really need a cooler, but obviously it will help. You could also look at water injection rather than IC, it is relativly cheap and easy to install and is very effective IMO.
|
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
Keep in mind a small compressor housing will heat air real bad..Just keep an eye on it....
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| shoey50 |
|
||
|
EBXR8380 wrote: Keep in mind a small compressor housing will heat air real bad..Just keep an eye on it....
so does that mean having a bigger cooler would be a good idea in this case? |
||
| Top | |
||
| redrocket |
|
||
|
ok... so u guys think that id b right in runnin low boost say 4-6 psi?? custom make a manifold, scrap the cooler idea and get chiptorque or somone like that 2 reprgram the chip? keepin in mind that all im after is a tad more power id b f**k happy with anythink over 200fwkw. wats a rising reg worth?
|
||
| Top | |
||
| EB on boost |
|
||
|
redrocket wrote: ok... so u guys think that id b right in runnin low boost say 4-6 psi?? custom make a manifold, scrap the cooler idea and get chiptorque or somone like that 2 reprgram the chip? keepin in mind that all im after is a tad more power id b f**k happy with anythink over 200fwkw. wats a rising reg worth?
You will still need the cooler... |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 19 guests |
