|
| corey munday |
|
||
|
Hi ppl, i was wondering if anyone on here has built ther own log style turbo manifold and if so do they have any pics? I'm going to have a go at building my own manifold over the next couple of week and will keep you posted on the progress.
Regards Corey |
||
| Top | |
||
| schnoods |
|
|||
|
I have built a couple of custom manifolds for a few mates (an rx7 and a lancer) which isnt really isnt that difficult.
First get a flange to suit your car ( an exhaust shop have these to suit most cars ) and bolt it to your head. then get your turbo flange and position it in your engine bay for clearances. Once u have a desired position measure it up the take the turbo flange and tack a brace from the exhaust flange to the turbo flange. then getting steam pipe bends start from the turbo flange first then from the exhaust flange and meet up in the middle. its also good to go back every now and then to check clearances etc. another tip is to try and get all the piping and bends somewhat even . hope that helps a bit.
_________________ Because of Beer, Thirst is a Beautiful Thing! |
|||
| Top | |
|||
| corey munday |
|
||||||
|
Hi guys, just an update. I started to make the manifold today. Firstly I got some 90*10 mild steel 620mm long, found the centre of the plate and marked out the 6 holes. Each of the holes have 104mm centres. Then i got a 41mm hole saw and drilled the holes checking with the manifold gasket as i went. This is as far as i got as i did this at work today and ran out of time. Here are some pics.
Regards Corey
|
||||||
| Top | |
||||||
| JOSE |
|
|||
|
Dont forget spark plug notches!.
Be carefull when welding as 10mm mild steel is pretty easy to warp, so i suggest you get a scrap head from somewhere to bolt i to while you weld it
_________________ Because i can. |
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
I can get them flange plates for $50..
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| ebs_4l |
|
||
|
geez hes keen making the entire head flange!!! as ebxr said, usually cost bout $50 to buy. the ones i use are from pacemaker
_________________ EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI |
||
| Top | |
||
| balizticbobo |
|
|||
|
I get them for nothing...
Just dont tell the boss!
_________________ 13.28@103.73mph |
|||
| Top | |
|||
| balizticbobo |
|
|||
|
double post... my bad
_________________ 13.28@103.73mph |
|||
| Top | |
|||
| Andrew J |
|
|||
|
Personally i think youre pretty game drilling those holes with a holesaw! Must have taken for ever!
_________________ The problem with America is stupidity. I'm not saying there should be a capital punishment for stupidity, but why don't we just take the safety labels off of everything and let the problem solve itself?
|
|||
| Top | |
|||
| corey munday |
|
||
|
Only took .5hr to drill all 6 holes and i drilled the bolt holes today all matches up nicely. The steel cost me bugger all as I work for an engineering firm so the manifold is really only going to cost me my time. I will post some pics in the next few days when its bolted to the head(which i have to give a bit of a clean first)
Regards Corey |
||
| Top | |
||
| ebs_4l |
|
||
|
what r u gonna make it with?? u got steampipe elbows?
working for an engineering firm, dont they have a drill bit that big?? and yes, i have made my own exhaust manifold 
_________________ EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI |
||
| Top | |
||
| Mr.Kiss |
|
|||
|
Any updates for us???
_________________ My Cars |
|||
| Top | |
|||
| Eu-GenixX |
|
||
|
{USERNAME} wrote: what r u gonna make it with?? u got steampipe elbows?
working for an engineering firm, dont they have a drill bit that big?? and yes, i have made my own exhaust manifold thats a nice looking manifold... |
||
| Top | |
||
| corey munday |
|
||||||||
|
Hi guys just an update. the manifold is now finished bar the wastegate mount as still unsure where i'm going to put it as the motor hasn't been fitted to the car yet. Enough talk anyways here are some pics and let me know what you think. PS. EBS 4L that is a nice manifold but something that big wouldn't fit under the bonnet of a TD corty
 
Regards Corey (cortEA)
|
||||||||
| Top | |
||||||||
| Mr.Kiss |
|
|||
|
Looking good, i'm gonna try make something like soon.
_________________ My Cars |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 24 guests |
