|
| charlie4401 |
|
||
|
I would just like to know wat size intercooler piping I should run?????? 3" or 2.5" THe car is a EF falcon runing any were form 5 to 10psi.
|
||
| Top | |
||
| 104ord |
|
|||
|
3 inch is wat i run for 10 lb the bigger the better
_________________ if the bar aint bendin your just pretendin |
|||
| Top | |
|||
| FLASH |
|
|||
|
Bigger is better for flow with high psi, smaller is better for response on low psi = good boost at low rpm.
But im sure ill be flamed for even the suggestion of running 2.5. I ran it, no probs as yet 
_________________ FALCAHOLIC |
|||
| Top | |
|||
| charlie4401 |
|
||
|
wat boost r u runing????
|
||
| Top | |
||
| Johnson stroker |
|
|||
|
you will get away with 2.5inch up to about 7-9 psi, depends on your cooler too as to what you plan to do.
What are your intentions and what are you trying to achive?
_________________
|
|||
| Top | |
|||
| FLASH |
|
|||
|
{USERNAME} wrote: wat boost r u runing????
He said up the top between 5-10 which is a pretty broad range. Maybe he's intent on running boost spike 
_________________ FALCAHOLIC |
|||
| Top | |
|||
| madeaspack |
|
||
|
iv got 2.5" currently running 11-12psi but any more than this and i get detonationat a pretty low load part of the map with a very safe amount of timing,so im upgrading to 3" now,with a custom plenum with front mount xf throttle body,this will eliminate a lot of bends too
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| FLASH |
|
|||
|
What plenum did you get? Nizpro, Snort? how much $
_________________ FALCAHOLIC |
|||
| Top | |
|||
| madeaspack |
|
||
|
im making the plenum will cost about $150 for parts and welding and lots of man hours (well about 10)
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| EFFalcon |
|
|||
|
2.5" here, Snort Plenum and 11psi.
no issues from it.
_________________ FALCN6 - EF GLi Turbo, 20" Rims, Air Bag Suspension, Straight LPG, 225rwkw |
|||
| Top | |
|||
| Dansedgli |
|
||
|
My AU ran 2.5 inch piping. 308rwkw.
|
||
| Top | |
||
| frankieh |
|
|||
|
excellent.. good to know.. I plan on running a max of 10psi and aiming for 250rwkw.. was counting on 2.5" to be sufficient.. you good folk have just convinced me that it is.
|
|||
| Top | |
|||
| twr7cx |
|
|||
|
I wish I had rather gone 2.5" for the supercharger.
|
|||
| Top | |
|||
| FLASH |
|
|||
|
{USERNAME} wrote: iv got 2.5" currently running 11-12psi but any more than this and i get detonationat a pretty low load part of the map with a very safe amount of timing,so im upgrading to 3" now,with a custom plenum with front mount xf throttle body,this will eliminate a lot of bends too
Can i ask are the xf throttle bodies bigger? Ive never looked at one. Make sure you do a thread on the custom plenum are you using the bbm bottom or is it full custom?
_________________ FALCAHOLIC |
|||
| Top | |
|||
| madeaspack |
|
||
|
bbm bottom just making the top half,the xf throttle is much bigger,prob not necessary but iv got one so i'll use it
_________________ 97 el xr6,5 speed short shifter,sequential scoop,no arial,freshly resprayed,low on 17's,3 inch zorst,stainless hi flo cat,snort stage 3 stainless manifold,garrett t04e,front mount cooler,wolf 3d ecu,seimens 760cc injectors,walbro fuel pump |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 30 guests |
