|
| 104ord |
|
|||
|
whats the best way to run the pipe work for a baxt turbo should i get the standard pipes that are 4kms long? or buy a aftermarket set up or has any one built a kit with tubes and elbows? it isnt a ford turbo cooler with the inlet and outlet on the same sides.
_________________ if the bar aint bendin your just pretendin |
|||
| Top | |
|||
| sexyr6 |
|
|||
|
good question i'd like some answers two...
|
|||
| Top | |
|||
| abcdefghi |
|
||
|
I will be in touch with an engineer tomorrow to ask that very question. Specifically can I cut 3" holes into my engine bay walls?
|
||
| Top | |
||
| bfhoon |
|
|||||
|
go the full kit.
the stock pipework sux a**, the best way iv seen is to use the underbattery spot for the airfilter in the inner guard and use an in out style cooler removing the stock airbox and using the space to run the cold pipes around the inlet side. this keeps the radiator heat and the turbo heat away from the cold pipes. have a look in my gallery, there are 2 kits there to see. i cant post pics at work. mine is from plazmaman racing.
_________________ bf xr6turbo siemens injectors, full plazmaman 800 hp intercooler kit, 5 inch cat and custom dual 2.5 inch zorst, billet flywheel with mal wood clutch kit, braided hoses, big brakes, 3.2L surge tank/w twin 044's rebuilt motor with forged and billet everything 420+ rwkw on 98. holden killer. Last edited by bfhoon on Tue Mar 18, 2008 11:13 am, edited 3 times in total. |
|||||
| Top | |
|||||
| 104ord |
|
|||
|
i like the first kit what is one like that worth?
_________________ if the bar aint bendin your just pretendin |
|||
| Top | |
|||
| bfhoon |
|
|||
|
2250 whole kit. all pipes cooler filter and silicone hoses with clamps return hoses everything needed to fit.
_________________ bf xr6turbo siemens injectors, full plazmaman 800 hp intercooler kit, 5 inch cat and custom dual 2.5 inch zorst, billet flywheel with mal wood clutch kit, braided hoses, big brakes, 3.2L surge tank/w twin 044's rebuilt motor with forged and billet everything 420+ rwkw on 98. holden killer. |
|||
| Top | |
|||
| twr7cx |
|
|||
|
Get the full big boy Plazmaman kit with the plenum and everything - not cheap, but it's the shibniz!
|
|||
| Top | |
|||
| 104ord |
|
|||
|
its an ba xt which im boosting ive already got a big cooler, garrett t3/t4 turbo. its got a gt front bar on it with my air intake all sorted out. i just need turbo to cooler and cooler to throttle body pipe work. i have access to all the 3inch alloy tube i can handle... is it hard to plumb it this way with elbows ect. or better just to get a kit?
_________________ if the bar aint bendin your just pretendin |
|||
| Top | |
|||
| bfhoon |
|
||||||||
|
when i get home i will post up pics of the car without the front bar so you can see where the pipes go.
you will have trouble getting 3 inch under the passenger headlight, best thing is to use a silicone hose under the light or cut a 3.5 inch hole in your inner guard where the old airbox was and run the solid pipe through this hole. as for the hot pipes from the turbo to the intercooler you will have trouble there too, using silicone hoses and alloy pipe is also needed here. the pre mentioned fabricator has seperate kits for pipework hot and cold side and can be sold seperatly, as long as your turbo points down it should fit. chef// rapidsystems or plazmaman xr6turbo developments all can hook you up.
_________________ bf xr6turbo siemens injectors, full plazmaman 800 hp intercooler kit, 5 inch cat and custom dual 2.5 inch zorst, billet flywheel with mal wood clutch kit, braided hoses, big brakes, 3.2L surge tank/w twin 044's rebuilt motor with forged and billet everything 420+ rwkw on 98. holden killer. |
||||||||
| Top | |
||||||||
| 104ord |
|
|||
|
thank for your help i might go for a pipe work kit looks great and more simple. might cost more but looks the part ......thanks bfhoon
_________________ if the bar aint bendin your just pretendin |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 38 guests |
