|
| djuman |
|
||
|
hi guys, prob 100's of threads already on this but have had a look and cant find anything...
im thinking about forced induction and i am jus curious as to wat mods i can do to get my engine ready???
_________________ '98' EL XR6 Pacemaker headers, 2 1/2 inch (header back) exhaust with Hi-Flow CAT, IC&E coil and 9mm leads, NGK plugs, billet short throw shifter >147.9rwKw
|
||
| Top | |
||
| TURBO_GHIA |
|
|||
|
depends on what power your looking for ,if you only want 200kw then nothing ,if you want 400kw full rebuilt with the best of everytihng
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| sly |
|
||
|
What TURBO_GHIA said, except (in the 200kW case) do a compression test and have the ECU scanned for any error codes that indicate faulty sensors. Any problems will be greatly magnified by boost.
Also start thinking about rebuilding/upgrading your tranny. You won't need to do this straight up, but the odds are you will need to do it eventually. It'll be less painful if you've already decided who will do the job and what they'll do to it.
_________________ AU1.5 Wagon, Raptor ProStreet kit, Pacemaker 4499's with 3" collector, 3" metal cat, 3" pipe, Pex BSO660 & BSO439, BA brakes, Sprintgas mixer LPG system, Airod variable-venturi mixer... stealth FTW Sniper tuned! |
||
| Top | |
||
| EBXR8380 |
|
|||
|
Spend the $$ on good ecu and tune.. Things like injectors and fuel delivery to keep up with power levels.. The 255 Walbro pump is the cheapest, reliable and 42Lb injectors.. Will get you 250 rwkw but more so the torque around 900 FtLb...Compare that to other motors.....Forget about T5's...
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| djuman |
|
||
|
so i take it that a T5 wont take the pressure then??? any suggestions?
if i go for an aftermarket ECU, bigger fuel pump, and injectors befor i get a charger put on will that have any negative effects on my car now?? was thinking of doing some engine mods any way (port and polish, reseating valves bla bla bla) and i have heard that if i shave a little bit off the head or use a smaller gasket with forced induction it can cause pinging... is this true
_________________ '98' EL XR6 Pacemaker headers, 2 1/2 inch (header back) exhaust with Hi-Flow CAT, IC&E coil and 9mm leads, NGK plugs, billet short throw shifter >147.9rwKw
|
||
| Top | |
||
| ea_falcon |
|
||
|
yes that is true i got my head shaved and a AU gaskit and it pings its a*** of with normal fuel
_________________ 02 series 3 AU marline ute 5speed 347 stroker |
||
| Top | |
||
| djuman |
|
||
|
so i went down to my local performance guys and they were a little unclear on wat kind of trans upgrade i could do.
any reconmendations or suggestions about getting the old trans strong enough to handle a flogging?? have to get the extention housing and the bush for the tail shaft fixed next week so while its out i was thinging of getting some tranny work done. maybe a new clutch and might get my flywheel machined while im there. again any suggestions
_________________ '98' EL XR6 Pacemaker headers, 2 1/2 inch (header back) exhaust with Hi-Flow CAT, IC&E coil and 9mm leads, NGK plugs, billet short throw shifter >147.9rwKw
|
||
| Top | |
||
| sly |
|
||
|
A T5z or T56 perhaps. Mal Wood in Brisbane would be best place to start for info. Some of the Supra boxes may suit as well.
_________________ AU1.5 Wagon, Raptor ProStreet kit, Pacemaker 4499's with 3" collector, 3" metal cat, 3" pipe, Pex BSO660 & BSO439, BA brakes, Sprintgas mixer LPG system, Airod variable-venturi mixer... stealth FTW Sniper tuned! |
||
| Top | |
||
| djuman |
|
||
|
cheers heaps guys. will def have a look at mal woods. seen some cars with his stuff and the look pretty good
_________________ '98' EL XR6 Pacemaker headers, 2 1/2 inch (header back) exhaust with Hi-Flow CAT, IC&E coil and 9mm leads, NGK plugs, billet short throw shifter >147.9rwKw
|
||
| Top | |
||
| schnoods |
|
|||
|
tko600.
_________________ Because of Beer, Thirst is a Beautiful Thing! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 23 guests |
