|
| TURBO_GHIA |
|
|||
|
hey guys
how do you retard the timing on an EL ,and whats a good starting point for a turbo setup ,its only running low boost has started injectors ,walbro fuel pump,and standard fuel reg cheers jarrod
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| TerroristGHIA |
|
|||
|
EMS, or Wolf, Best way to retard timing
Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
dont have an aftermarket ecu yet ,just need to know how to do it with the dizzy
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| EFFalcon |
|
|||
|
need to put the car in self test mode, then retard the dizzy.
no idea how much you'd need.
_________________ FALCN6 - EF GLi Turbo, 20" Rims, Air Bag Suspension, Straight LPG, 225rwkw |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
how do you put it in self test mode ,do you bridge to pins or something ?
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| ebs_4l |
|
||
|
bridge the two left hand (top and bottom) pins in the test port located near the fuse panel under the dash.
id set it probably 0deg base since im not sure of the max timing figure compared to the base figure, id guess they would run upto about 25deg adv in standard form, and you wouldnt want more than 15deg advance in it without a tune, therefore, instead of setting the timing at 10deg base, you set it at 0deg base.... the el only has 1 timing mark right?? that mark is 10deg adv im sure, so set it to about 1cm to the right of that mark... the car will be crappy off boost, but you have to put up with that when you try to retain a non-tuned ecu......
_________________ EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI |
||
| Top | |
||
| stockstandard |
|
|||
|
There are instructions for setting the timing here - http://www.fordmods.com/forums/viewtopic.php?t=33978
As for how much timing to pull, how much boost are you running? The general tuning instructions I have used to set base timing maps in the past suggest pulling 2 degrees from the maximum advance per lb of boost to a maximum of 1/2 to total advance (this would be a very safe tune). In reality, how much you can get away with will depend on lots of factors. Running rich and cool with low boost and you might not have to touch it. I would pull as much timing as practical and creeping it forward until your happy. If you ever hear so much as a tick from the engine pull it back a couple of degrees and leave it.
_________________ Stoke me a clipper, I'll be back for Christmas |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
so do i retard the timing or advance it ,i think i have a 6 psi spring could be wrong tho
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| EFFalcon |
|
|||
|
retard the timing.
_________________ FALCN6 - EF GLi Turbo, 20" Rims, Air Bag Suspension, Straight LPG, 225rwkw |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
so when you move the dizzy one way it advances it and when you move it the other it retards it ? and then you look at the timing mark on the and it will show you where the timing is depending on the way or you the dizzy is that right ??
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| Steady ED |
|
|||
|
Yes, turning dizzy clock wise will retard it.
anti-clockwise advances.
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
arh ok cool ,its all clicking now ,
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
Turn dissy same rotation as rotor button to retard....I'd fit the XR6 fuel reg or fit an adjustable one...
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
so anyone have a starting point of what degress to retard it ? - 10 to much to start with ??
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| ebs_4l |
|
||
|
start at 10 as per my post above, put it this way, you are better off starting too retarded then starting with to much advance
_________________ EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 25 guests |
