|
| my el project |
|
|||
|
want 500rwkw...
its an el falcon and its at mechanics getting pulled down now for build.. wat pistons war rods wat crank wat size turbo wat computer, or is chip taque able to preforme wat brand planem wat size injectors wat coil syetem any advice or stuff iv forgot.. and prices would be great... diff and grear boxs and fuel syetem sorted.. 
_________________ El Futura
|
|||
| Top | |
|||
| 3.9from hell |
|
||
|
standard crank can stay, balanced, crack tested etc
rods can also stay or you could go Atomic, spool etc obviously block would need to be tested for core shift, cracks etc then main bearing tunnel line bored, decked square etc etc pistons could go many ways, Atomic etc, altho ebs_4l has seen 530rwkw on cast ACLS..... some serious headwork and valve springs 130psi seat pressure cam from Surecam, aprox .550" lift, 290 duration, 112 LS turbo would want to be sumthing like a GT4202r, or mabey a T51r tubular manifold from snort etc, sum people will say 50mm runners but they are perhaps not needed, plenty of succesful combos running 40mm or smaller ideal ecu will vary but a J3 chip is definatly out at this level IMHO, Autronic, motec, EMS mabey? Snort are making some realy nice plenums now, or a Nizpro BA turbo one will be good biggest injectors you can get your hands on 1000cc plus crane HI6 ignition seems a popular choice you will need a surge tank fed by a bosch 040 or similar, then two external pumps, bosch 044 etc, 1/2'' fuel lines or 2 smaller 5/16'' lines, custom fuel rail with feeds on both ends and return line out in the middle forget any gearbox ever intended for your car, T56, Tremec TKO, or a supra R154 c4 auto, built to every bolt gona want a 4'' exhaust price all up? think 15-20grand minimum |
||
| Top | |
||
| 4dlvr |
|
||
|
{USERNAME} wrote: want 500rwkw... its an el falcon and its at mechanics getting pulled down now for build.. wat pistons war rods wat crank wat size turbo wat computer, or is chip taque able to preforme wat brand planem wat size injectors wat coil syetem any advice or stuff iv forgot.. and prices would be great... diff and grear boxs and fuel syetem sorted.. do you have 50k to blow?????
_________________ 96 EF FAIRMONT |
||
| Top | |
||
| jerrytorry |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: want 500rwkw... its an el falcon and its at mechanics getting pulled down now for build.. wat pistons war rods wat crank wat size turbo wat computer, or is chip taque able to preforme wat brand planem wat size injectors wat coil syetem any advice or stuff iv forgot.. and prices would be great... diff and grear boxs and fuel syetem sorted.. do you have 50k to blow????? i can not see in any way that it could cost 50K to build a 500rwkw falcon motor. he's already got the driveline and fuel system sorted all he needs is a motor and the turbo parts to go onto it
_________________ |
|||
| Top | |
|||
| 67RCE |
|
||
|
A motor to handle 500rwkw will cost $6-10k, fuel system - $4.5k, turbo setup + manifold - $6k. exhaust - $3k, ECU + Tune - $4k, ignition setup - $2k, box to handle power - $5k, tailshaft - $1.5k, diff to handle power - $5k. There is $37-41k.
_________________ ILL60 - EF XR8, Sunroof, Ticky Kit, 19x8.5/19x11 TE37's, 347, AFr185's, TFS BoxRcustom converter, Hurst Quarterstick, huge billet cam. |
||
| Top | |
||
| 4dlvr |
|
||
|
{USERNAME} wrote: A motor to handle 500rwkw will cost $6-10k, fuel system - $4.5k, turbo setup + manifold - $6k. exhaust - $3k, ECU + Tune - $4k, ignition setup - $2k, box to handle power - $5k, tailshaft - $1.5k, diff to handle power - $5k. There is $37-41k. plus unexpected things going wrong and small other bits not mentioned easy $5k 500rwkw is not a small amount of power mate, add another 10k to get the power to the ground properly. trust me mate if it cost under $20k id have 500rwkw already
_________________ 96 EF FAIRMONT |
||
| Top | |
||
| TROYMAN |
|
||
|
for those who remember pyroay's el xr6 turbo..
he spent over $40'000 to get 451.5rwkw.. then another $20'000 on drive train and brakes so good luck getting 500rwkw!!! |
||
| Top | |
||
| 67RCE |
|
||
|
{USERNAME} wrote: {USERNAME} wrote: A motor to handle 500rwkw will cost $6-10k, fuel system - $4.5k, turbo setup + manifold - $6k. exhaust - $3k, ECU + Tune - $4k, ignition setup - $2k, box to handle power - $5k, tailshaft - $1.5k, diff to handle power - $5k. There is $37-41k. plus unexpected things going wrong and small other bits not mentioned easy $5k 500rwkw is not a small amount of power mate, add another 10k to get the power to the ground properly. trust me mate if it cost under $20k id have 500rwkw already Yes, a cooler to handle that much power - $2k, Cooler piping assuming 3" stainless - $1k. The 6-10k for the motor is if you do 90% of the work, otherwise, expect $10-15k. So $45-50k EASY! that is without even thinking about making the car stop, which is another $5-10k.
_________________ ILL60 - EF XR8, Sunroof, Ticky Kit, 19x8.5/19x11 TE37's, 347, AFr185's, TFS BoxRcustom converter, Hurst Quarterstick, huge billet cam. |
||
| Top | |
||
| EBXR8380 |
|
|||
|
Some prices are way off there...
I'm still using my std driveshaft and diff... Brake upgrades are not that expensive now days...
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| 3.9from hell |
|
||
|
yeah i was gona say. 3grand for an exhaust? farrk off
pm ebs_4l he ownes the only 500rwkw E series on here i can think of |
||
| Top | |
||
| 4dlvr |
|
||
|
{USERNAME} wrote: Some prices are way off there... I'm still using my std driveshaft and diff... Brake upgrades are not that expensive now days... you have a 2 piece tail shaft and lsd standard, he doesn't, plus i mean so disrespect with this at all but i cant imagine you give would flog the beast off the line to often, ive herd of lsd's dying after about 250rwkw or so
_________________ 96 EF FAIRMONT |
||
| Top | |
||
| 67RCE |
|
||
|
{USERNAME} wrote: {USERNAME} wrote: Some prices are way off there... I'm still using my std driveshaft and diff... Brake upgrades are not that expensive now days... you have a 2 piece tail shaft and lsd standard, he doesn't, plus i mean so disrespect with this at all but i cant imagine you give would flog the beast off the line to often, ive herd of lsd's dying after about 250rwkw or so When did EB XR's come standard with a 2 piece shaft? With 500rwkw, I'd be building the entire car as strong as possible.
_________________ ILL60 - EF XR8, Sunroof, Ticky Kit, 19x8.5/19x11 TE37's, 347, AFr185's, TFS BoxRcustom converter, Hurst Quarterstick, huge billet cam. |
||
| Top | |
||
| needfordspeed |
|
||
|
I know for a fact it costs well under 50k to get over 500rwkw and 143+ MPH
Anyway, buy the kit "hiboost" is selling, it's proven and not a bad price for what it is. It's in the for sale section. And if your asking all these questions you got no chance, this is a dreamer thread and I'd put money on this never happening. But i'd be stoked if I was proved wrong. Some of the above advice is a load of crap, call a workshop who's been involved with a 500rwkw falcon, they'll tell you how it is.
_________________ 1988 EA S-Pack|MPI|LSD|AIT turbo manifold|Garrett GT3540|3" Exhaust turbo back|Resprayed|microtech LT8s|60lb Injectors|Bosch 044 with surge tank|3000 RPM stall|Ported AU head|Wade turbo cam|Crow double valve springs|1.3mm MLS headgasket|C4 conversion|Built bottom end|10.6@125MPHi |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 14 guests |
