|
| 910HWI |
|
||
|
what turbo do you have on EF-EL i6 when does boost kick in
_________________ Wanted Dead or Alive - 1996 EFII XR6, "910HWI", 5 speed man, dark blue, venom front bar, 17" CSA Gladiators, green/gold perl bonnet vents. |
||
| Top | |
||
| Tocchi |
|
|||
|
mines a T66 equivalent, but i built it up from a garrett T04
front 0.70 A/R, front wheel = 84mm with 66mm inducer rear 1.15 A/R, rear wheel = 75mm rear wheel i guess i reach "0 psi" around 3500rpm http://tinypic.com/player.php?v=vo8y2c&s=3 |
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
T04Z .84 A.R spools 2500 Similar to T66 with water cooled centre and ball bearing shaft... The 3000 converter makes it a cruiser or bruiser...
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| fritzz |
|
|||
|
to4z with .84a/r turbine housing
from data log it has about 1psi at 1800rpm and 12psi from just under 3000rpm.
_________________ # 1997 EL Falcon GLI - 600+rwkw |
|||
| Top | |
|||
| mustang6 |
|
||
|
Well i have just put a turbo on my 4.0L in my mustang .. The turbo is like a t25 LOL reaches Full boost by about 2500 rpm and goes all the way to my redline... and booost gauge says its reading around 8-10 psi.
_________________ 1966 mustang 4Litre GT45, 560cc injectors, Walbro 550intank, 4spd auto 2700stall,Ems Stinger. |
||
| Top | |
||
| Grimketel |
|
|||
|
{USERNAME} wrote: mines a T66 equivalent, but i built it up from a garrett T04
front 0.70 A/R, front wheel = 84mm with 66mm inducer rear 1.15 A/R, rear wheel = 75mm rear wheel i guess i reach "0 psi" around 3500rpm http://tinypic.com/player.php?v=vo8y2c&s=3 from the vid you can hear it start to wind up at 3000, and then it smashes it right on 4 grand. is yours a manual or auto?
_________________ enough isn't enough |
|||
| Top | |
|||
| Tocchi |
|
|||
|
auto
|
|||
| Top | |
|||
| ebs_4l |
|
||
|
gt3582r 1.06 rear. from my datalog i reach 1psi at 1800 like fritzz, and will see 16psi at about 2900
_________________ EB 4L, 8.4:1, R154, GT4202r, 4in exhaust, Greenslade Engineering exhaust manifold, plenum chamber, 90mm throttle, Garrett W2A cooler, Surecam custom, autronic SM4, Bosch 120lb, Crane HI-6, LX-92, LM-1, Turbosmart Reg, 2x bosch 044, turbosmart 48 gate. 470kw+ @ 18PSI |
||
| Top | |
||
| BI6TIM |
|
||
|
KKK800r, 0.96 rear housing (not sure on rear wheel size or trim), 0.7 front housing with 70mm inducer.
Not sure about 1psi but 10psi comes on strong at 3000rpm. |
||
| Top | |
||
| FairmontEFturbo |
|
||
|
T04E, $350 job off ebay, bush bearing. hits 1psi bout 2000rpm and full 8psi not to much later! been thrashing it over a year and its still like new!
|
||
| Top | |
||
| turbotrana |
|
||
|
it can be difficult comparing the turbine a/r from one type of turbo to another. eg a 0.84 a/r in a TO4Z may be comparable to a 1 a/r in a smaller framed turbo. So you should keep this in mind when comparing
_________________ Turbo 6s rule |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 35 guests |
