|
| damianm79 |
|
||||||||
|
Finally after 12 months... built and ready to go in the car...
What's every1 think?? Here's the list of parts used. Scat 347 Crank H beam Rods 30thou pistons Mains girdle HV Oil pump HE 7L Sump Holley Alloy heads w/ 2.1" Intake and 1.6" Exhaust (highly ported) FMS X303 Roller cam Roller rockers 1.6 RR Hardened Pushrods BBK SSI Intake (highly modified) FMS 42lb Injectors w/ high flow fuel rail Barry Grant Fuel Pressure Regulator BG EFI Fuel Pump Russel 6AN fuel hose from tank-surge pot-fuel rail CSR Electric Water Pump March Aluminium Pulley Kit Crane Hi-6 Digital Ignition Crane Billet Electronic Distributor Crane LX-92 Electronic Coil Wolf 3D ECU CentreForce Dual Friction Clutch Kit Yella Terra Explosion Proof Fly-Wheel Spent about $14k...... so far... lol
|
||||||||
| Top | |
||||||||
| damianm79 |
|
|||||
|
final
|
|||||
| Top | |
|||||
| XH5LWEPN |
|
|||
|
Looks great mate, Whats it going into?
Using standard block?
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| Damo |
|
|||
|
looks farrkkking schweeeeeeet!!!
|
|||
| Top | |
|||
| wild_ef |
|
|||
|
looks n sounds like it pretty nice
wat kind of car is it going into? wat sorta power u hoping for?
_________________ BA Fairmont Ghia |
|||
| Top | |
|||
| cjh |
|
|||
|
That looks fvcken awsome, should go hard, eh?
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| XR9UTE |
|
||
|
What are the flow figures for the heads and intake?
Pete. |
||
| Top | |
||
| damianm79 |
|
||
|
Going into an EL XR8...
Not entirely sure on power output.. hoping for minimum 250rwkw. Also got 100hp of Blue Bottle Fun onboard.. Heads flowed 550hp potential at .050 and with intake and short exhaust runners 470hp potential. And I got a weathered block from an AU series 2... I heard they had a higher nickel content... and the machinist agreed.. he said the Boring tool really laboured boring the block.. (and it was a new sharp tool) Couldn't afford a DART block at the time.. |
||
| Top | |
||
| XR9UTE |
|
||
|
{USERNAME} wrote: Heads flowed 550hp potential at .050
and with intake and short exhaust runners 470hp potential. .. No I mean actual flow figures and at what test pressure? At a glance 42's are unnecessarily large for that engine unless you're going to use them to supply fuel for the 100 shot? Pete. |
||
| Top | |
||
| Steady ED |
|
|||
|
Are they CAT roller rockers?
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| damianm79 |
|
||
|
I can't find the flow sheet... I have it somewhere though.. I'll see if I can find it and post back...
I realise the 42lb's are a bit big... but they are fuelling for the NOS as well.. I just got them at an incredible price... $400 for the set.. and they are Siemen Dakas injectors. I'm hoping the ECU tune can accomodate for them.. And the Rollers.. were badged FMS... not sure who manufactured them... they are a full bearing roller though.. |
||
| Top | |
||
| chooka |
|
||
|
Nice work keep us posted.
_________________ ----------------------------------------------------
|
||
| Top | |
||
| phatal |
|
||
Age: 42 Posts: 517 Joined: 3rd Dec 2004 Ride: SZ Titanium & ZG Fairlane Location: Roxby Downs |
is it going to fit under the bonnet with that manifold? looks nice!
_________________
|
||
| Top | |
||
| damianm79 |
|
||
|
Not entirely sure mate.. lol
I measured from the valley to the top of the stock one, and this one is 4cm taller... Worst comes to worse... a BA bonnet bulge in the loom.. |
||
| Top | |
||
| MICKYYYY |
|
||
|
Another tuff 347 going into a E series falcon
Love it
_________________ Wanted Either Capri/Cortina/XY/XW/XR/XT with tough V8 stroker engine, auto, 9inch, upgraded brakes etc[/SIZE][/size][/color] |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 26 guests |
