|
| SBR |
|
|||
|
hi guys
im soon to be purchasing a EF xr8( fingers crossed), and was wondering wether 200rwkw, was a fairly easy achievable task? and if so wat would be needed aside from exhaust. i had in mind doing complete exhaust, manifold, cams, and plugs. 
_________________ " If you aint first, Your last!" |
|||
| Top | |
|||
| Timmeh |
|
||
|
75mm MAF from Mr Landau and get a SVO 75mm throttle body.
I'm in the same boat as you. I'm looking at easy bolt ons that increase power. |
||
| Top | |
||
| SBR |
|
|||
|
yeah bolt on is really wat im after.
_________________ " If you aint first, Your last!" |
|||
| Top | |
|||
| EDXR8 |
|
|||
|
200rwkw is about the max for the 5L and requires a lot of work and money. You will need to change heads, intake, cam, roller rockers, injectors, MAF, TB and exhaust to get there. Then you will probably need EEC mods to tune it properly.
|
|||
| Top | |
|||
| Timmeh |
|
||
|
What kind of power would you get if you did the following to the 5.0L
Injectors Fuel pump Throttle Body MAF Extractors and Ehaust K&N filter Cheers Thats about all I'd do to it. |
||
| Top | |
||
| EDXR8 |
|
|||
|
{USERNAME} wrote: What kind of power would you get if you did the following to the 5.0L
Injectors Fuel pump Throttle Body MAF Extractors and Ehaust K&N filter Around 130-140rwkw maybe. You don't really need larger injectors, fuel pump or throttle body until you have changed heads/intake IMO. Instead of those mods I would do: Pro-M 75mm MAF YT 1.72 Roller rockers Extractors and Exhaust Underdrive pullies K&N filter/CAI setup This should give better results and should be around the same cost if not cheaper. |
|||
| Top | |
|||
| Timmeh |
|
||
|
What will the 1.72 roller rockers do for power?
I'm not sure which version Windsor I have in the 97 EL Fairmont Ghia so I wouldnt know what to order parts wise. I'f changing rockers would it be best to get new springs and stuff as well? Cheers |
||
| Top | |
||
| EDXR8 |
|
|||
|
{USERNAME} wrote: What will the 1.72 roller rockers do for power?
I'm not sure which version Windsor I have in the 97 EL Fairmont Ghia so I wouldnt know what to order parts wise. I'f changing rockers would it be best to get new springs and stuff as well? Cheers Roller rockers give you extra power because the reduce valvetrain friction. The 1.72 ration (stock is 1.6) also gives more vlave lift which helps too. Should see 5-10rwkw improvement with them, Yella Terra ST-2027 rockers are very good quality, direct bolt on and cost around $500. You don't need new springs because it is only a small increase in lift. |
|||
| Top | |
|||
| Timmeh |
|
||
|
I guess I have a hydraulic lifter camshaft then and not a solid?
Cheers ED XR8. Anything else you can think of bolt on wise that would help without changing ECU would be appreciated. Cheers again. |
||
| Top | |
||
| SBR |
|
|||
|
s pretty much its all upper block and head work needed, wat kind of power would u get wit those mods u talked about? also how much did ur setup cost edxr8
_________________ " If you aint first, Your last!" |
|||
| Top | |
|||
| EDXR8 |
|
|||
|
{USERNAME} wrote: I guess I have a hydraulic lifter camshaft then and not a solid? Cheers ED XR8. Anything else you can think of bolt on wise that would help without changing ECU would be appreciated. Yeah the Windsor 5L runs a hydraulic roller camshaft. There aren't many other value for money mods, as I said the heads and intake need to be changed to get any decent power but they are expensive. {USERNAME} wrote: s pretty much its all upper block and head work needed, wat kind of power would u get wit those mods u talked about? also how much did ur setup cost edxr8
Yeah thats it, basically keep the short motor change the rest. With the simple mods I listed you would be lookign at around 140-150rwkw I would think, thats about the limit with the stock heads and intake. As for my setup I am scared to add it up. |
|||
| Top | |
|||
| One Drone |
|
|||
|
I've done most of the bolt on stuff (except tb as HO intake is small anyway and the pump) and that is about all you can do on the stock engine. To really make them breathe you must have heads, intake, cam, rollers etc!! No one said V8s come cheap..
_________________ There are 10 types of people in this world. |
|||
| Top | |
|||
| XR8Chic |
|
|||
|
I have only JUST got over 200rwkw on my N/A 5L XR8
this is what I have... Manifold: Edelbrock Performer RPM upper intake manifold, and edelbrock lower manifold. Heads: AFR 185cc heads. (CNC ported, complete heads with double valve springs) Cam: Crane Cam PowerMax 2031 Rockers: Yella Terra ST2027 roller rockers. (1.72 ratio) Engine Management: EEC-IV & UniChip (tuned by Croydon Autosports) MAF: 75mm PRO M (Chrome) TB: 65mm SVO Throttle body Injectors: 30lb Ford Motorsport injectors, adjustable fuel regulator. Leads: 10mm Magnacore Leads Airfilter: K&N Pod Airfilter Extractors: Pacemaker Big bore, Stainless Jethot coated. Cats: Supercats hi flow cats (2.5" opening) Exhaust: Lukey single 3" mandrel bent system.
_________________ 1993 ED XR8 - Poly Green |
|||
| Top | |
|||
| SBR |
|
|||
|
id hate to ask u how much all that was xr8chic?
_________________ " If you aint first, Your last!" |
|||
| Top | |
|||
| 4.9 EF Futura |
|
|||
|
{USERNAME} wrote: I have only JUST got over 200rwkw on my N/A 5L XR8
Its probably worth noting tho - that it's a very strong 200rwkw and by the sounds of it, goes all day every day and seems like it doesnt give you much trouble.... probably also worth noting that 200rwkw is a lot of power.
_________________ I promise..... I will never die. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 11 guests |
