Fordmods Logo

balancer 

 

Page 1 of 1 [ 11 posts ] 

 
 Post subject: balancer
Posted: Thu Aug 10, 2006 10:41 pm 
Tyre Shredder
Offline

Age: 44

Posts: 311

Joined: 10th May 2005

Ride: ebxr8

Location: melbourne
VIC, Australia

what is the imbalance on a eb 5litre windsor, 50 oz?

 

_________________

347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse

Top
 Profile  
 
 
Posted: Thu Aug 10, 2006 11:36 pm 
EFI Guru
Offline

Age: 59

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

yep.
Top
 Profile  
 
 
Posted: Thu Aug 10, 2006 11:38 pm 
Tyre Shredder
Offline

Age: 44

Posts: 311

Joined: 10th May 2005

Ride: ebxr8

Location: melbourne
VIC, Australia

thanks pete

 

_________________

347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse

Top
 Profile  
 
 
Posted: Fri Aug 11, 2006 12:01 am 
EFI Guru
Offline

Age: 59

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

no wuckers greg!
Basically from '82 5.0's went with the 50oz imbalance because the crankshaft centre counterweights were shrunk down in mass. This necessitated the imbalance to be moved outside the engine...on the flywheel and balancer. If you get a chance to look at an old 302 crank next to an '82-up type you'll see what i mean. Also note that these late blocks are a considerably lighter casting, 25lb's lighter in fact. This is why the factory engineering rating was reduced from 500hp to 350hp on the late blocks.

Pete.
Top
 Profile  
 
 
Posted: Fri Aug 11, 2006 8:47 pm 
Tyre Shredder
Offline

Age: 44

Posts: 311

Joined: 10th May 2005

Ride: ebxr8

Location: melbourne
VIC, Australia

pete can u give me the run down on how to activate the thermos with the tweecer. i want them to switch on to high when they come on. so i can get rid of the craig davies switch on it thanks
Greg

 

_________________

347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse

Top
 Profile  
 
 
Posted: Mon Aug 14, 2006 11:29 am 
EFI Guru
Offline

Age: 59

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

Yep, pin 41 will drive the low side of your fan relay(use a relay with a flyback diode and at least 40A capacity). The parameters are in Caledit...I will post the settings when I get home.

Pete.
Top
 Profile  
 
 
Posted: Mon Aug 14, 2006 6:34 pm 
Tyre Shredder
Offline

Age: 44

Posts: 311

Joined: 10th May 2005

Ride: ebxr8

Location: melbourne
VIC, Australia

ok no probs

 

_________________

347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse

Top
 Profile  
 
 
Posted: Tue Aug 15, 2006 11:21 am 
EFI Guru
Offline

Age: 59

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

Sorry I forgot.

Pete.
Top
 Profile  
 
 
Posted: Tue Aug 15, 2006 10:02 pm 
Tyre Shredder
Offline

Age: 44

Posts: 311

Joined: 10th May 2005

Ride: ebxr8

Location: melbourne
VIC, Australia

when ever you get a chance mate

 

_________________

347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse

Top
 Profile  
 
 
Posted: Wed Aug 16, 2006 12:22 am 
EFI Guru
Offline

Age: 59

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

Hi Greg,

Find these in the Scalars list.
This is how I set my 1DDC in the ute to turn on the fans at 190F and off again at 180F.

Fan_high_speed_any_load_temp = 180
Fan_high_speed_high_load_temp = 190
Fan_low_speed_temp = 180
Fan_present = 1
Fan_two_speed_enable = 1

Pete.
Top
 Profile  
 
 
Posted: Wed Aug 16, 2006 6:16 pm 
Tyre Shredder
Offline

Age: 44

Posts: 311

Joined: 10th May 2005

Ride: ebxr8

Location: melbourne
VIC, Australia

thanks mate ill give it a go

 

_________________

347, crane cam, Pro topline 180 heads, Edelbrock victor efi intake, 80mm C&L maf, 75mm tb, 30lb injectors and 1/4 horse

Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 11 posts ] 

Who is online

Users browsing this forum: No registered users and 35 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Wed Dec 25, 2024 4:53 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names