|
EBXR8380 |
|
|||
|
I had spacers made up to fit 8.2 EFI induction .. I sold them to a guy on Corral.net...
Went with 8.2 Iron Eagle...
_________________ As in ZOOM 126 edition |
|||
Top | |
XR9UTE |
|
||
|
Just go straight for a 9.2 or 9.5...there's intakes galore for them.
There's a TFS-R for clevelands coming out in january too ....bout f**k time! |
||
Top | |
TerroristGHIA |
|
|||
|
{USERNAME} wrote: Just go straight for a 9.2 or 9.5...there's intakes galore for them. There's a TFS-R for clevelands coming out in january too ....bout f**k time! MMM the R series manifold. I rate them very highly, as seen on my tower of power 351W. Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
Top | |
crsmith |
|
||
|
TFS-R? Obviously a manifold off the windsor side. having them in the mustangs for a long time over there in the US led to a lot of development. How good is it, ie what does it bring to the table for the cleveland? Its a moot point anyway for my 400 as I would have to go the dreaded (expensive)spacer direction to fit it to my beast. I'm still waiting on Edelbrock to do one of their RPM-air gaps for the 400's.
|
||
Top | |
409Stroker |
|
||
|
600 reliable horse power out of a 302ci turning at 8000rpm LMAO How much money do you think this is going to cost....
Mate ive got a 393 turning to 7500rpm with 218cc CHI 3v's and all the fruit, god knows how much it makes but ide be thinking close to 500rwhp Fu*k all change out of 20K, machining the block alone was 2500,machining my heads was anouther 3 grand, theres 5 k just in machining Power is cheap reliability isnt , your chassing better figures than what guys at engine masters are screwing together and you want it to be reliable lol hahaha yer for 35K+ you might be lucky and it would only be a drag engine not for driving to the shops, go the turbo you'll make it but natraly asperated i think your pushing s**t up hill... or maybe closer to dreaming...
_________________ If you have it under control then you dont have enough power..
|
||
Top | |
XR9UTE |
|
||
|
{USERNAME} wrote: TFS-R? Obviously a manifold off the windsor side. having them in the mustangs for a long time over there in the US led to a lot of development. How good is it, ie what does it bring to the table for the cleveland? Its a moot point anyway for my 400 as I would have to go the dreaded (expensive)spacer direction to fit it to my beast. I'm still waiting on Edelbrock to do one of their RPM-air gaps for the 400's. Well, they made 540hp with a pair of their new C heads on 383ci cleveland. Why don't you use a CHI C-400 intake? Aussie made and the best 400 intake available. |
||
Top | |
daboss |
|
||
|
back again your comments made me think a bit so I have revised my specs,
block-dart 8.2 deck 4.125 bore, 8.2 because it is a legal replacement block heads-302 cleveland iron,4V valves, have seen them produce over 600hp on a 351 c and it works out cheaper plus I am old school crank-2.87 stroke(289 crank) pistons-have found a set to fit a 347 stroker which runs a 5.4 rod,all I could find out was the bore size 4.125 but they fit inline valve heads, pavtek have a 4.155 piston which they use on their 434 stroker that has chi heads(canted valves clevo) question-1- I have read a great deal on the pros of log rods(worked for boss 302)but recently read about c.h(compression height),raise one the other lowers, if I am chasing revs I need the long rod but a half decent c.h over 1.1 would be good,so does anyone know of a mob here in melbourne that could nut this problem out with me -2-did want to run a tunnel ram style manifold with a triple choke on top to act as the throttle body but can't find anybody here that makes manifolds,so my next set up will be an 8 throttle body set up, can get the manifold,thinking hayabusa efi set up cheaper than everything else but can anybody see any problems,there is a new gas system that will work with these,if not feasible then is there a mob that can make a manifold for me. I have a brother who will build the motor for me free because it's not your average wack a cam in drop on a manifold throw in a stroker etc etc,so I am banking on 25 to 30 grand considering a V8 supercar motor costs around 40 g and they machine the s**t out of the block heads etc etc for weight purposes . |
||
Top | |
XR9UTE |
|
||
|
What, and you think this will be legal!? BaaaaaHaaarrrrhahahahahaha.
|
||
Top | |
braad |
|
|||
|
{USERNAME} wrote: What, and you think this will be legal!? BaaaaaHaaarrrrhahahahahaha. It's interesting though, if it gets off the ground
_________________ Previous - |
|||
Top | |
XR9UTE |
|
||
|
{USERNAME} wrote: {DESCRIPTION} {USERNAME} wrote: What, and you think this will be legal!? BaaaaaHaaarrrrhahahahahaha. gas mate ever heard of it and its benefits Oh yeah sorry gas fixes everything. |
||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 10 guests |