|
| millard455 |
|
|||
|
hi all,
im after peoples opinion/advice on this cam. http://www.compcams.com/Cam_Specs/CamDe ... =1068&sb=2 will be used in a street driven 363ci windsor with AFR 185cc comp heads any help would be great as im a complete novice when it comes to stuff like this. thanks.
_________________ EL XR8 SERIES 2, 5SPD, HOT CHILLI RED, 200 ODD RWKW OF V8 FUN AND GAMES |
|||
| Top | |
|||
| XR9UTE |
|
||
|
That looks like a good'n. Have you got dyno2k?
|
||
| Top | |
||
| millard455 |
|
|||
|
{USERNAME} wrote: That looks like a good'n. Have you got dyno2k? dyno2k, is that a computer dyno program? nah i dont have it, my computer doesnt have much free space  so you think it would be a good choice? or is there any other recommendations?
_________________ EL XR8 SERIES 2, 5SPD, HOT CHILLI RED, 200 ODD RWKW OF V8 FUN AND GAMES |
|||
| Top | |
|||
| XR9UTE |
|
||
|
Yes, and yes I think it's a good choice. Put all your requirements to Comp for a custom cam and see how close it gets to that cam.
|
||
| Top | |
||
| BOTTLEDUP |
|
|||
|
The Crane HR232 is a better choice for a street driven 363ci Windsor... It will make as good top end power, with better mid range than the Comp XFI.
Here is build on the same combo you're planning using the Crane...  http://www.fordforums.com.au/showthread ... 393&page=2 http://www.pertheseries.com/forums/inde ... 216&st=240
_________________ TE50 T1 P01 |
|||
| Top | |
|||
| banarcus |
|
|||
|
Can you still get Crane stuff because the last time I checked things went pear shaped
|
|||
| Top | |
|||
| millard455 |
|
|||
|
{USERNAME} wrote: The Crane HR232 is a better choice for a street driven 363ci Windsor... It will make as good top end power, with better mid range than the Comp XFI. Here is build on the same combo you're planning using the Crane... http://www.fordforums.com.au/showthread ... 393&page=2 http://www.pertheseries.com/forums/inde ... 216&st=240 thanks for the heads up on that cam mate, ill have a dig around on the crane site and see what i can find. love that blokes XR8. now i know what XH5LWEPN meant when he said its going to be a torque MONSTER  was really good to see the results of pretty much exactly the same combo. banarcus, yeah you can still get CRANE gear.
_________________ EL XR8 SERIES 2, 5SPD, HOT CHILLI RED, 200 ODD RWKW OF V8 FUN AND GAMES |
|||
| Top | |
|||
| Snillorh |
|
||
|
G'day millard555,
As a side note - if you run a COMP grind be sure to install a composite distributor gear - COMP cams have been known to wear excessively if you run a stock hardened dissy gear. Piece of mind. |
||
| Top | |
||
| XR9UTE |
|
||
|
{USERNAME} wrote: G'day millard555, As a side note - if you run a COMP grind be sure to install a composite distributor gear - COMP cams have been known to wear excessively if you run a stock hardened dissy gear. Piece of mind. Actually you just need to run a -9 cam which is made of steel rather than the -8 cam which are austempered iron. I found this out the hard way...3 cams in 3 engines! You also need to use the zinc additive they make. Trouble with comp is they supply -8 cams unless you specify a -9 and they are useless when it comes to help with these problems. |
||
| Top | |
||
| XCSEDAN |
|
|||
Age: 35 Posts: 88 Joined: 28th Oct 2007 Ride: EDXR6, XC Falcon, EL2XR8 Location: Beveridge |
bit late now. but the aforementioned cam is a 300rwkw cam.
_________________ 1977 XC Sedan Project: Poo Brown, 351 toploader 9" . 1998 EL Series 2 XR8: Oxford Green 5spd manual. DEAD (KANGAROO) |
|||
| Top | |
|||
| BOTTLEDUP |
|
|||
|
{USERNAME} wrote: bit late now. but the aforementioned cam is a 300rwkw cam. That's quite a generalised statement! It won't go near 300rwkw without a very good set of heads, intake, exhaust, injectors etc... If you model this cam in Engine Analyzer software you'll find it has quite low dynamic compression, it opens the exhaust valve too early and you need to put a bunch more static comp in for it to be effective.
_________________ TE50 T1 P01 |
|||
| Top | |
|||
| XCSEDAN |
|
|||
Age: 35 Posts: 88 Joined: 28th Oct 2007 Ride: EDXR6, XC Falcon, EL2XR8 Location: Beveridge |
{USERNAME} wrote: {USERNAME} wrote: bit late now. but the aforementioned cam is a 300rwkw cam. That's quite a generalised statement! It won't go near 300rwkw without a very good set of heads, intake, exhaust, injectors etc... If you model this cam in Engine Analyzer software you'll find it has quite low dynamic compression, it opens the exhaust valve too early and you need to put a bunch more static comp in for it to be effective. that it is. i just know what i have seen it produce on a dyno (which again can vary dyno to dyno). the entire engine setup is critical no matter what you are doing. so i agree with you. for what its worth i remember the following details of that engine 12:1 compression (on pulp) MSD ignition AFR 185s (not sure what series but im guessing they would have had work done) 347 stroker. not sure on intake tb or maf size. cant remember what size extractors or pipes it had either.
_________________ 1977 XC Sedan Project: Poo Brown, 351 toploader 9" . 1998 EL Series 2 XR8: Oxford Green 5spd manual. DEAD (KANGAROO) |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 26 guests |
