|
| gunit18 |
|
||
|
getting some custom msd 8.5mm leads made. which boots for which cylinders need the 90degree bend boots? (i have gt40p's) can get them for 100 bucks.
also replacing spark plugs with normal ngk's. is there anything else i can replace on the spark side to give more spark? |
||
| Top | |
||
| offyaguts |
|
||
|
MSD coil
Distributor Iridiums Good leads |
||
| Top | |
||
| gunit18 |
|
||
|
i didnt think EL's came with the coil pack?
does anyone know wat leads need the 90degree boot onto the sparkplug, to clear the paccies? |
||
| Top | |
||
| gunit18 |
|
||
|
or am i thinking of something totally different?
|
||
| Top | |
||
| fordzatmyplace |
|
||
|
{USERNAME} wrote: i didnt think EL's came with the coil pack?
does anyone know wat leads need the 90degree boot onto the sparkplug, to clear the paccies? EL's don't come with coil pack But all dizzy cars still have one singal coil that supplys spark to the dizzy
_________________ ^^^ What He Said
|
||
| Top | |
||
| offyaguts |
|
||
|
That's what I am talking about.....not a coil pack but the one that hooks up to the centre plug on the dissy
All you need is the leads with the 90 degree boot.....if i get a chance i'll have a look and see what ones mick webb put on mine, I know they are 8mm ones, i'll go and check |
||
| Top | |
||
| offyaguts |
|
||
|
They say Hi Energy Silicon Supression 8mm.....maybe Hi Energy is the brand but that is what Mick put on it
|
||
| Top | |
||
| gunit18 |
|
||
|
how is ur car going? i mite try get some of these msd ones, only 100 bucks and replace plugs too.
wat cam u running? |
||
| Top | |
||
| data_mine |
|
|||
|
I needed a custom length coil to dizzy lead when I upgraded to a full Crane HI6 ignition system, was late Saturday and needed to get the car going again, so got a long Bosch lead, cut it and recrimped it. Worked fine.
_________________ 1998 DL LTD in Sparkling Burgundy, daily, 302W, stereo, slow |
|||
| Top | |
|||
| gunit18 |
|
||
|
how much was the crane HI6 ignition system? wat it include n where u get it from? if i get the ignition system upgraded, i'll get the custom leads.
|
||
| Top | |
||
| data_mine |
|
|||
|
~$450 included HI6 module and a LX-92 coil to match.
Got it from Mark Tanswell (ttransar at bigpond dot net dot au)
_________________ 1998 DL LTD in Sparkling Burgundy, daily, 302W, stereo, slow |
|||
| Top | |
|||
| gunit18 |
|
||
|
where does he work? and is there any improvement in any areas?
|
||
| Top | |
||
| gunit18 |
|
||
|
just off topic, would there be any advantages over using 30lbs with maf over 24lbs FMS injectors? as ive got 186rwkw with 19's and stock maf, anyone reakon i could break 200rwkw with 30's and matching maf?
|
||
| Top | |
||
| data_mine |
|
|||
|
Got a generally stronger bottom end (important as I've got a highly strung cam that doesn't com eon til about 3000rpm), and 3 or 4 RWKW up top. Throttle response is much quicker.
{DESCRIPTION} Excuse run 15 as I had the chip in economy mode. Run 13 started highe rup the power wise, but peaked earlier and lower. 16/17 highlights the quicker acceleration offered (by the steeper start). I'm now doing better with a free flowing intake. {DESCRIPTION} edit: found the receipt. Star Performance 2A Regatta Road, Five Dock, NSW, 2046 Ph: 02-9747-2200
_________________ 1998 DL LTD in Sparkling Burgundy, daily, 302W, stereo, slow |
|||
| Top | |
|||
| offyaguts |
|
||
|
{USERNAME} wrote: just off topic, would there be any advantages over using 30lbs with maf over 24lbs FMS injectors? as ive got 186rwkw with 19's and stock maf, anyone reakon i could break 200rwkw with 30's and matching maf?
I reckon it would be hard to break 200rwkw with the setup you have, the heads probably aren't quite up to the task. If your thinking of going supercharger, I would sit on the 186rwkws with the 19lb injectors and wait until you get the blower and go straight to 42lb or even a little bigger cause at the moment it doesn't look like your injectors are holding you back cause that is about the power figure you should expect from your setup. My car is going pretty well, no issues yet but need to increase low down torque, she's a little slow off the line so i'm chasing up a stall converter as we speak. I went the Trickflow Track Heat stage 1 cam, very nice and lumpy and when it comes on song you definately know its there. Also thinking of a unichip just to get it right in the tune department. It goes on the dyno in two weeks so i'll let you know how it goes. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 5 guests |
