|
Kilma |
|
|||
|
I have read the box intakes aren't all that effective until you are running mass boost. Would that still be the most effective intake for around 15 psi?
_________________ The fast fun: Suzuki GSXR1000
|
|||
Top | |
XR9UTE |
|
||
|
{USERNAME} wrote: I have read the box intakes aren't all that effective until you are running mass boost. Would that still be the most effective intake for around 15 psi?
This was true of earlier designs where the upper was effectively just a box on top of the lower with next to no runner length. Long runner length is required to build torque(the reason the small 5.0 Ford engine makes good torque is due in large part to this), shortening the runner length usually(but not always) increases top end power at the expense of low end torque. This is true whether normally aspirated or not. The TFS-R with box upper is very similar in it's design to the TS50 Ford intake in that there are still some staggered runners with bellmounths inside the box. Of course the TS50 engine has a larger capacity, therefore it can afford to give up some runner length that would otherwise have created a torque deficiency on smaller displacement engine. Pete. |
||
Top | |
MICKYYYY |
|
||
|
What comp you running?
_________________ Wanted Either Capri/Cortina/XY/XW/XR/XT with tough V8 stroker engine, auto, 9inch, upgraded brakes etc[/SIZE][/size][/color] |
||
Top | |
EBXR8380 |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: I have Twisted wedge heads but any afterarket head will make power when air is forced in there..In my case I'm using turbo's. I have them set up so rpm runs out around 6500 so there not much chance of over rev etc.. Plus ecu rev limit setting... Sorry to hijack the thread but how did you get the rpm to run out at 6500. Did you just pick some heads that were suited up to 6500rpm on a standard stroke engine, and any higher then that and their flow just drops off? NO I have rev limiter set soft at 6500 and hard at 6800 rpm.. Mainly due to Hydro cam & heavy roller lifters.. The turbine housings are .63 also. Fitted with T04 sized T350 P trim 61mm wheel X's two..More than enough... TFS track heat heads flowheaps esp ported by Gatt bros... Besides with 588 rwhp there's traction issues...
_________________ As in ZOOM 126 edition |
|||
Top | |
Chich |
|
||
|
Just took a look at the Trickflow Box-R manifold and apparently you need aftermarket fuel rails to run the thing.
http://store.summitracing.com/partdetai ... =1&N=700+0 Do aftermarket rails exist or would these need to be made up as a custom jobbie?
_________________ V8 Windsor here we come..... |
||
Top | |
EBXR8380 |
|
|||
|
That's due to the std rails only supporting 500 h.p...
There are plenty of aftermarket rails around...[U.S- summit or Jegs] We made our own from alloy bought fr $50 a meter drilled holes for injectors 13.5 mmX 12m deep @ 20* angle then 1/8 into rail .. Then welded superflow fittings on ends.. They can be drilled and tapped also ... They are much cheaper to mke yourself, but without changing them power is limited...http://store.summitracing.com/partdetai ... toview=sku pics http://store.summitracing.com/largeimag ... S-51580001 Fuel reg is included due to having higher fuel flow a bigger return is required ... Some pics of my rails .. this is early the fuel reg is at the front between fuel rails now
_________________ As in ZOOM 126 edition |
|||
Top | |
MICKYYYY |
|
||
|
I currently have a 347 bottom end and thinking of going bigger, Could my allloy heads & trickflow intake fit straight onto a 351w block???
_________________ Wanted Either Capri/Cortina/XY/XW/XR/XT with tough V8 stroker engine, auto, 9inch, upgraded brakes etc[/SIZE][/size][/color] |
||
Top | |
EBXR8380 |
|
|||
|
You'll have to buy another TFS "lower" manifold as block is wider.. The heads will bolt on.. You MAY have to drill head bolt holes in head alittle bigger as 351's have 1/2 bolts...No big deal..
_________________ As in ZOOM 126 edition |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 31 guests |