Fordmods Logo

EB 351W 

 

Page 1 of 2 [ 16 posts ] Go to page 1, 2  Next

 
 Post subject: EB 351W
Posted: Fri Jul 01, 2005 8:51 pm 
Fordmods Newbie
Offline

Posts: 1

Joined: 1st Jul 2005

Location: Melbourne
VIC, Australia

I currently have an EB Fairmont Ghia with a old 5.0L in it. Near 400k. Nursing it along just nicely. I am looking at buying a short motor in the near future and setting it up with a nice set of Edelbrock Alloy heads and manifold. I have come across a good deal on both 302w short roller motors and 351w roller shorts.

My question is, will I fit the 351 in the EB and has anyone had any joy with the Edelbrock manifolds on a 351w? (ie: fitting them in height wise) I am looking at the Performer RPMII manifold and the Performer RPM heads.

Cheers
Top
 Profile  
 
 
Posted: Fri Jul 01, 2005 10:35 pm 
Getting Side Ways
Offline
User avatar

Age: 71

Posts: 3555

Joined: 7th Nov 2004

Gallery: 4 images

Power: 482 rwkw

Location: Penrith
NSW, Australia

Heads fit though 1/2 head bolts..May have to drill out bolt holes in head..
Inlets are differant..The lower manifold is wider...
Need a custom sump..The rear mains are bigger & 5.0 sumps don't fit..A Hi-energy fits just right,should have one anyway??
The engine sits 3" higher so you'll need a bonnet scoop or cowling...A B.A lookalike...Though I'd use 70-76mm maf with 24 Lb callibraion it will run with existing efi gear...It will be tight around exhaust but it can be done...
Graeme...hth...

 

_________________

As in ZOOM 126 edition
331 Dart block,3.25/ 4340 steel crank, Oliver rods,TFS ported track heat heads, TFS track heat inlet Twin SC61 turbo's
Project 1UZ-EF has started.. S475 Turbo 4.0 V8 Mustang Celica.....

Top
 Profile  
 
 
Posted: Sat Jul 02, 2005 6:32 am 
Getting Side Ways
Offline
User avatar

Age: 53

Posts: 3763

Joined: 25th Nov 2004

Gallery: 6 images

Ride: EFII 5.8 NOS TerroristGhia

Power: 274 rwkw

Location: Sydney Australia
NSW, Australia

How much can you get the short 351, i would be interested in this as well
Brett

 

_________________

The Terrorist ED Retired due to RUST.
The TerrosistGhia, EF Ghia 351 EFI 5 Speed.
Millennium Falcon, Sleeper EL DOHC 6 Speed Manual EFI LPG
Member#1131
I didn't Vote for Multiculturalism, DID YOU!!!

Top
 Profile  
 
 
Posted: Sat Jul 02, 2005 2:29 pm 
Getting Side Ways
Offline

Age: 43

Posts: 7287

Joined: 5th Nov 2004

Gallery: 12 images

Ride: 1994 ED XR8 Sprint

Location: Somewhere in
QLD, Australia

IIRC most of the edelbrock heads are drilled for 1/2" head bolts, and you use sleeves to space them down for 302 use

 

_________________

Banned

Top
 Profile  
 
 
Posted: Sat Jul 02, 2005 3:10 pm 
Getting Side Ways
Offline
User avatar

Age: 44

Posts: 1052

Joined: 12th Nov 2004

Ride: NC II Fairlane

Location: Newcastle
NSW, Australia

theres a 351 ed in street fords issue 2 and it only mentions that it needs a extra inch of deck height so you need a scoop,but appart from that it was a easy swap with the car turning over 1st time with the standard xr8 computer.

cheers

 

_________________

"Looking at cleavage is like looking at the sun. You don't stare at it. It's too risky. You get a sense of it and then you look away."

Now with el thermos fitted.

Top
 Profile  
 
 
Posted: Tue Jul 05, 2005 11:45 am 
Tyre Shredder
Offline

Posts: 366

Joined: 1st Jul 2005

Location: perth
WA, Australia

{USERNAME} wrote:
theres a 351 ed in street fords issue 2 and it only mentions that it needs a extra inch of deck height so you need a scoop,but appart from that it was a easy swap with the car turning over 1st time with the standard xr8 computer.


ummmmm nc5ltr..... how? different firing order!

 

_________________

OFFICIAL TOKEN BLACKY

Top
 Profile  
 
 
Posted: Tue Jul 05, 2005 11:53 am 
Getting Side Ways
Offline
User avatar

Age: 71

Posts: 3555

Joined: 7th Nov 2004

Gallery: 4 images

Power: 482 rwkw

Location: Penrith
NSW, Australia

same fireing order..The early 302's are differeant...

 

_________________

As in ZOOM 126 edition
331 Dart block,3.25/ 4340 steel crank, Oliver rods,TFS ported track heat heads, TFS track heat inlet Twin SC61 turbo's
Project 1UZ-EF has started.. S475 Turbo 4.0 V8 Mustang Celica.....

Top
 Profile  
 
 
Posted: Wed Jul 06, 2005 5:22 pm 
EFI Guru
Offline

Age: 59

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

Here.....

http://www.fordmods.com/forums/viewtopi ... highlight=

http://www.fordmods.com/forums/viewtopi ... highlight=

BTW deck height difference is 9.5"- 8.2" = 1.3" which results in a 3" overall higher engine. I'm using an Edelbrock Peformer 5.8 intake #3884 lower and Performer upper in my XE ute. The RPMII intake requires port matching to fit the 351 lower ports but get this...They don't sell it separately so you have to buy the whole 5.0L RPMII kit and sell off the lower!?!
Wasnt a problem for me as I am only building a mild torque monster of an engine for my XE. The #3884 lower and Performer upper combo is 10.83" high. I had to trim some metal out of the bonnet bracing on my XF bonnet otherwise it fits but the throttle body is very close. If I have contact issues when actually running I will fit a shaker. For an E series I would say contact is more likely but I believe the Edelbrock intake is actually slightly lower than the GT40. I'd grab another bonnet from the wreckers to save cutting your original.
Other things you'll need are;
351w TFI distributor
XR-Y pacemaker headers and weld in some HEGO bosses
Longer fuel rail crossover tubes (cut the originals off)
Bigger fuel pump unless it's going to be stock.
351w front Sump and pan mounted dipstick tube
Minimum 65mm t-body
With Edelbrock heads and intake you'd need at least 24lb injectors.
Reduced base circle roller cam(for pre '94 blocks) and pushrods to suit.
These roller shorts you refer to should have an F4TE engineering number(check before you buy). Non roller EFI blocks are E9TE.
Beef up your BTR 4spd...it won't like the torque of the 351.
A TwEECer to dial it in properly.

Cheers,
Pete.
Top
 Profile  
 
 
Posted: Wed Jul 06, 2005 9:42 pm 
Tyre Shredder
Offline

Posts: 366

Joined: 1st Jul 2005

Location: perth
WA, Australia

oi pete, you wont remeber me, but i out the wheels on xr9 at beaurepaires when dean was there! whats this tweecer deal? i got rid of my gs and bought myself a ed xr8 and its boring the s**t out of me and i want more grunt, i know your the eec guru, so what can i do with the computer?

 

_________________

OFFICIAL TOKEN BLACKY

Top
 Profile  
 
 
Posted: Thu Jul 07, 2005 1:04 am 
EFI Guru
Offline

Age: 59

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

Oi whatever your name is....yes I remember you. I just talked to Dean today actually.
Let me know what your EEC catch code is and I'll let you know how much TwEECer support there is. Should be something like 3DEA,3DFA or the like.
Having said that a TwEECer won't give you grunt unless you do some something to the engine to warrant recalibrating it.
While we're on the subject..351 it...that'll give you some grunt!

Cheers,
Pete.
Top
 Profile  
 
 
Posted: Thu Jul 07, 2005 5:09 pm 
Tyre Shredder
Offline

Posts: 366

Joined: 1st Jul 2005

Location: perth
WA, Australia

where could i get the engine mounts from? are they custom? ill check with dean to see if they have any long injected windsor at superoo, but im definatly interest in the 351 option, by the way my names wade!! cheers pete.

 

_________________

OFFICIAL TOKEN BLACKY

Top
 Profile  
 
 
Posted: Thu Jul 07, 2005 6:09 pm 
EFI Guru
Offline

Age: 59

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

Small block is a small block...mounts are the same Wade.

Pete.
Top
 Profile  
 
 
Posted: Thu Jul 07, 2005 9:20 pm 
Tyre Shredder
Offline

Posts: 366

Joined: 1st Jul 2005

Location: perth
WA, Australia

OK dont get narky! lol, ill ring deano and suss it out, how much for you to do your thing with the computer?, i search the web and found your web page with robs super bird on it, and he reckons its a good thing! high 13s or something wasnt it?

 

_________________

OFFICIAL TOKEN BLACKY

Top
 Profile  
 
 
Posted: Fri Jul 08, 2005 1:51 am 
EFI Guru
Offline

Age: 59

Posts: 4359

Joined: 5th Nov 2004

Gallery: 28 images

Ride: 351 Vogue,XH 5.0,'17 5.0 Stang

Location: Perth
WA, Australia

Trust me Wade they won't have any injected windsors at superoo.
Ring brunswick diesels and see if they have any. Don't pay more than about $1000 for a complete EFI 351.
Otherwise you're better off buying a 351w short and then buy the parts you need to finish it.
No... Robs XA(and then XB) did mid 14's. You get that when you don't even rebuild the engine or clean up the welds where I cut and shut the upper intake!?!?!...Dodgy bastard! Mid to low 14's with a dead stock engine and 3:1 gears is pretty damn good though.
Just changing the intake will get you into the high 13's.

Pete.
Top
 Profile  
 
 
Posted: Mon Aug 01, 2005 4:25 am 
Parts Gopher
Offline

Age: 47

Posts: 97

Joined: 3rd Apr 2005

Ride: 98 F.B.T

Location: Ferntree Gully
VIC, Australia

To xr9ute where did you say you could get a 351 windsor short i already have SVO heads and trickflow intake with 90mm throtle bodie as i would like to fit a 351 widsor into my DC LTD. I would like to find out a price on recalibrating my original ECU thanks.
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 2  [ 16 posts ]  Go to page 1, 2  Next

Who is online

Users browsing this forum: No registered users and 21 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Mon Dec 23, 2024 2:12 pm All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names