|
| Timmeh |
|
||
|
Probably APC in Wangara. Thats the closest one I can think of.
I don't know if they are any good with the accuracy though. Got any recommendations? |
||
| Top | |
||
| XH5LWEPN |
|
|||
|
{USERNAME} wrote: Probably APC in Wangara. Thats the closest one I can think of.
I don't know if they are any good with the accuracy though. Got any recommendations? I'd use MCE in wangara mate, just as close and a bit better with their setting up etc.
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| Timmeh |
|
||
|
Have you got an idea on price? About $60 or so for a power run with AFRs.
|
||
| Top | |
||
| XH5LWEPN |
|
|||
|
{USERNAME} wrote: Have you got an idea on price? About $60 or so for a power run with AFRs.
I paid $80 for a power run through MCE before i did all the work. For that you should be able to get one printout with AFR's and one with torque.
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| XH5LWEPN |
|
|||
|
Well Timmeh, as you know, the clutch has arrived. So now its time to get it fitted up with ya new Yella Terra f/wheel and get this puppy on the dyno. I think im almost as excited as you are
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| Timmeh |
|
||
|
HAHAHAHA.
Yeah. Shes getting a polish all this week. A couple of panels a day as it takes me about 1 hour per two panels. Shes going to look clean and go fast. I'll need to chat to you about MSD ignitions. Get that all sorted. Might even get a set of nice shiney valve covers. |
||
| Top | |
||
| XH5LWEPN |
|
|||
|
{USERNAME} wrote: I'll need to chat to you about MSD ignitions. Get that all sorted.
Mate, i'd just go for an MSD Blaster coil, MSD cap and rotor kit, MSD Leads and a set of new NGK's(If not already fitted). That should pretty much do you for now. I have never gone as far into MSD dizzy's and ignition boxes etc, so i cant advise into that, but i dont think you'll have any dramas running the above. Give Dave @ A1Hiperformance (BOTTLEDUP) a buzz, he'll sort you out and know exactly what your looking for.
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| Timmeh |
|
||
|
Cool. Thanks I'll do that then.
Will be able to make it today just after 4pm if it suits you to pick up my clutch kit. I'll give KEC a ring and see if they have my flywheel in yet. |
||
| Top | |
||
| XR9UTE |
|
||
|
Get a Crane Hi-6 and PS92 coil or an MSD digital 6 and matching coil. The old analog MSD6A is an unreliable piece.
The crane setup will be cheaper to buy. Make sure you grab a set of 3 piece underdrives from BPT if you haven't already. Pete. |
||
| Top | |
||
| Timmeh |
|
||
|
Yeah I've got under drives already Pete.
Crane Hi-6 and Ps92 coil. Check. Are these just plug and play? ie bolt on and drive away. Don't need to get a tune or anything? Thanks. Only thing I should be after now is a 65mm TB as the 58mm is maybe a touch on the small side. |
||
| Top | |
||
| XR9UTE |
|
||
|
Yeah they have instructions on how to wire them up...it's easy. You can even get a Ford 5.0 connection harness for it. Yes a 65mm is good for that combo.
|
||
| Top | |
||
| XH5LWEPN |
|
|||
|
{USERNAME} wrote: Only thing I should be after now is a 65mm TB as the 58mm is maybe a touch on the small side.
Spewin mate, you should of snapped that one up i had here, it got sold last week. Should be able to track another one down. I may have to look into those above reccomended ignition systems by Pete. What sort of differences do you see with them Pete?
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| TerroristGHIA |
|
|||
|
I will seel my 65mm If you want. PM me a price and allow 20 for postage. I also have a matching 65mm EGR for it
Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
| Top | |
|||
| XH5LWEPN |
|
|||
|
{USERNAME} wrote: I will seel my 65mm If you want. PM me a price and allow 20 for postage. I also have a matching 65mm EGR for it
Brett Haha, there ya go, sorted!!
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| Timmeh |
|
||
|
Yeah and the flywheel came in today.
Hopefully I can pick up the clutch kit from your tomorrow (sorry about today, I hate screwing people around) and then go to KEC and pick the flywheel up. Bomber has sent out the billet short shifters so next week I can line up the clutch and shifter install. Then within two weeks she'll hit the dyno. Also the EL GT MAF should arrive soon. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 59 guests |
