|
| XR9UTE |
|
||
|
Your thermostat controls the temp so it wouldn't be running any hotter.
|
||
| Top | |
||
| 79 raven |
|
|||
|
but the thermostat only controls the flow of water that the pump has put into the head
|
|||
| Top | |
|||
| XR9UTE |
|
||
|
{USERNAME} wrote: but the thermostat only controls the flow of water that the pump has put into the head and thereby controlling the temp. |
||
| Top | |
||
| Scaffy |
|
|||
|
Looks like another little test for Streetbuilt to do on the dyno. Run a stock 302 without underdrives, then fit a set with the car still on the rollers and run her up again...
_________________ Trickflow Street Heat top end kit, 70mm BBK TB & EGR, 24lb injectors, Underdrives & 3.73s: 275rwhp - 13.15@105mph NA / 12.37@116mph N20 |
|||
| Top | |
|||
| andy777 |
|
|||
|
Scaffy wish you guys were in sydney would have you tune my el xr8
jeff sent me down some underdrives fitted them up and you feel a difference on the bum0meter |
|||
| Top | |
|||
| Benny D |
|
|||
|
{USERNAME} wrote: Looks like another little test for Streetbuilt to do on the dyno. Run a stock 302 without underdrives, then fit a set with the car still on the rollers and run her up again... yea mate if you could kill this off once and for all would be great. be it either way, i would like to see the results.
_________________ BA XT V8. Ice Mint. 18" Speedys. XR6T LSD. Full Pacemaker twin 2 1/2inch Stainless Steel system. Custom CAI. Black XR interior with white trimming. Powerbond underdrive kit 25%. |
|||
| Top | |
|||
| Scaffy |
|
|||
|
Yeah, we'd just need to find a suitable car for the test. I suppose it wouldn't hurt to do it on an EB GT. Will try and get on to it after I get home in a couple of weeks.
Andy, I wish we had more E-series over here that I could have a play with. I might have to go over that way for a working holiday some time.
_________________ Trickflow Street Heat top end kit, 70mm BBK TB & EGR, 24lb injectors, Underdrives & 3.73s: 275rwhp - 13.15@105mph NA / 12.37@116mph N20 |
|||
| Top | |
|||
| TFORD8 |
|
|||
|
Hey, how do I order myself a set of the Ford racing ones for my EF? Im keen as...
_________________ EF2 XR8 Lowered on Genuine EL GT 17", Slotted + Drilled all round, Custom retrimmed ghia interior, competition stereo, DiFillipo headers, hi-flow cats, single muffler 3", K&N, custom maf/induction and rear window venetian |
|||
| Top | |
|||
| XR9UTE |
|
||
|
www.summitracing but I wouldn't get Ford racing ones.
|
||
| Top | |
||
| TFORD8 |
|
|||
|
How come? They not real good, have problems?
_________________ EF2 XR8 Lowered on Genuine EL GT 17", Slotted + Drilled all round, Custom retrimmed ghia interior, competition stereo, DiFillipo headers, hi-flow cats, single muffler 3", K&N, custom maf/induction and rear window venetian |
|||
| Top | |
|||
| XR9UTE |
|
||
|
Get steel ASP ones.
|
||
| Top | |
||
| TFORD8 |
|
|||
|
Ill look into it, thanks heaps.
Do they actually give a noticeable gain? Do I need replace idlers/tensioner pulleys too, or stock ones are fine?
_________________ EF2 XR8 Lowered on Genuine EL GT 17", Slotted + Drilled all round, Custom retrimmed ghia interior, competition stereo, DiFillipo headers, hi-flow cats, single muffler 3", K&N, custom maf/induction and rear window venetian |
|||
| Top | |
|||
| XR9UTE |
|
||
|
They produce a noticeable gain over the entire rev range. In fact they're the best performance bang for the buck on a 5.0.
|
||
| Top | |
||
| TFORD8 |
|
|||
|
So I was looking at the summit racing ones, and I dont know enough about them to understand what im looking at, which ones will fit, etc... They're for mustangs, not falcons, the crank looks too big, and the water pump is ribbed, on my xr8 water pump is smooth...
Ive also been thinking about this one http://www.bptmotorsport.com.au/home/pr ... detail/246 ?
_________________ EF2 XR8 Lowered on Genuine EL GT 17", Slotted + Drilled all round, Custom retrimmed ghia interior, competition stereo, DiFillipo headers, hi-flow cats, single muffler 3", K&N, custom maf/induction and rear window venetian |
|||
| Top | |
|||
| bluestripes |
|
|||
|
Hi Guys - found reading through this pulley post interesting, and I'm hoping someone with experiance can assist
 ) Situation - I've brought and installed an aftermarket WP pulley that measures 5.7in which is the same measurement as my AU HBalancer. The after market WP was a flow cooler and when it arrived the factory WP would not fit as it was to small and shallow... hence the only WP I could get to fit was the current spec mentioned. So now after reading up - i feel I have created an under driven set up which is good or have I misunderstood the concept ??? Also --- Question - is this a workable ratio for my engine ?? ( 347 ) Question - can my factory fan belt can be used ?? Thanks in advance - just trying to cover as many bases possible prior to install )
_________________ AU Ute ~ R350 |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 25 guests |
