|
| Capative Pit |
|
||
|
My car has a v8 in it but used to have only 175kw which is pretty s**t but now i did some mods
3 inch exhaust 4-1 Extractors , high flow cats Cold Air Intake K & N Air Filter Stage 2 Adjustable Shift Kit Monroe gt suspension superlow Kings springs how much kw does all those mods add up to and whats the next best upgrade to do on it to get it to 220kw |
||
| Top | |
||
| TROYMAN |
|
||
|
the 175/185kw has std gt40p heads, single valve springs, std rockers, 9.0:1 compression, 65mm throttle body std cam.
the 220kw has gt40p heads, larger valves, double valve springs, tella terra roller rockers, 9.4:1 compression ,port matched manifold, 70mm throttle body and different cam. given that you have headers, high flow cats and 3" exhaust and cold air intake you might have gained 15-20 kw.. the rest of the mods don't really add to the cars power out put.. |
||
| Top | |
||
| SWC |
|
||
|
"What the difference between au 175kw v8 and 220kw xr8?"
45kw 
|
||
| Top | |
||
| Capative Pit |
|
||
|
what mod should i get next i only have about $350 budget
|
||
| Top | |
||
| TROYMAN |
|
||
|
not much more you could do with that amount of money..
other things like cam. head work . j3 tuning will cost more than $350. you could get msd coils to add a slight improvement.. but it wont be much, lucky if 1kw would be gained imo.. |
||
| Top | |
||
| Mad2 |
|
|||
|
{USERNAME} wrote: "What the difference between au 175kw v8 and 220kw xr8?" 45kw LOL ...... dag...... . . . . |
|||
| Top | |
|||
| Capative Pit |
|
||
|
how much would it be to install a ts50 wing or lower it on ulralow spring(i have the springs) rear only
|
||
| Top | |
||
| TROYMAN |
|
||
|
if irsquote="Capative Pit"]how much would it be to install a ts50 wing or lower it on ulralow spring(i have the springs) rear only[/quote]
thats open to debate.. also depending on if you already have the wing and wether or not it needs painting.. most panel shops would paint and fit a wing for around $200. to fit the rear springs depends on wether it has irs or live axle. could cost anywhere from $70 to 150... if you like playing with cars you could do the rear springs your self. If irs you will need a spring compressor.. |
||
| Top | |
||
| SWC |
|
||
|
{USERNAME} wrote: {USERNAME} wrote: "What the difference between au 175kw v8 and 220kw xr8?" 45kw LOL ...... dag...... . . . . It answered the OP's heading question. Straight to the point  .
|
||
| Top | |
||
| Mad2 |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: {USERNAME} wrote: "What the difference between au 175kw v8 and 220kw xr8?" 45kw LOL ...... dag...... . . . . It answered the OP's heading question. Straight to the point .lol . . . i know
|
|||
| Top | |
|||
| blueblood |
|
|||
|
Underdrive pulleys can be found cheap.
_________________ 93 EB S-XR8 5 SPEED, |
|||
| Top | |
|||
| TROYMAN |
|
||
|
not for au though...
|
||
| Top | |
||
| Shortshift |
|
|||
|
{USERNAME} wrote: whats the next best upgrade to do on it to get it to 220kw How about some new valve springs? From reading up on V8 mods, a lot of guys in the US say the Ford springs are not good enough when the hp is increased. I've just bought a set of the Crane beehive springs for the GT40P heads for a bit over $200 (as I can't afford a few grand for aluminium heads at present). If you're going for an aggressive cam later on, you'll probably need double valve springs.
_________________ AU2 XR8 with Raptor VL, ported Yella Terra GT40P heads, Scorpion 1.6 RRs, XE264HR-14 Comp Cam, ceramic coated Hurricane Headers, 60lb injectors, Walbro 255, 200cfi cats, 3" exhaust & Snow Performance water methanol injection |
|||
| Top | |
|||
| xcabbi |
|
||
|
{USERNAME} wrote: not for au though... Compared to EB-EL, the AU is already underwritten from the factory. As for valve springs, they should be the first things to get replaced on a GT40P head. |
||
| Top | |
||
| WARMACHINE |
|
||
|
Au v8's are very very slightly underdriven from factory so much so that i wouldnt consider them under driven at all.
If some one made a set for the au id have bought them, i believe what stops everyone is the crank pulley has the encoder wheel attached to it. Underdriven au pulleys from factory... myth busted... |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 60 guests |
