|
| vik351 |
|
|||
|
I did this to my BA T
 cost SFA...
vik...Did it go any better???Make me feel better??? 
_________________ [b]BANNED[\b] |
|||
| Top | |
|||
| Whiteknight1 |
|
|||
|
Hehehe, havn't heard SFA in yonks, does it make the car run better vik???
_________________ Back in an E series! |
|||
| Top | |
|||
| Denney |
|
||
|
I ended up just cutting the holes. The piping through the front wouldn't of worked because of that black box in front of it (don't know what it's called. Didn't look at it to much). I'm thinking about maybe running some piping from the side down the the front bar but for now, it's all good.
Can't wait to get my cat back and new exhaust fitted. |
||
| Top | |
||
| fiftyone |
|
|||
|
relays for the lights i think. i had the same problem. the cold air comes in from the side, not the front anyway
_________________ ** For Sale ** {DESCRIPTION} |
|||
| Top | |
|||
| EBTS50 |
|
|||
|
has any 1 done mods to there EB V8 air box?? if so wat and dose it work
_________________ Ba Stock As A Rock |
|||
| Top | |
|||
| EBTS50 |
|
|||
|
bump
_________________ Ba Stock As A Rock |
|||
| Top | |
|||
| rushed |
|
|||
|
i would assume the same as the six cyl version. there are so many airbox mods now its not funny.
p.s. y would you bump when you posted 1 hour earlier? |
|||
| Top | |
|||
| EBTS50 |
|
|||
|
lol umm becasue i wana do it now
_________________ Ba Stock As A Rock |
|||
| Top | |
|||
| Falcs |
|
|||
|
postwhore!!
_________________ -------- Falcs -------- |
|||
| Top | |
|||
| jeffb |
|
|||
|
{USERNAME} wrote: has any 1 done mods to there EB V8 air box?? if so wat and dose it work
When I had my EB, I got a 90mm piece of PVC, cut a hole in the very bottom of the box, and cut a hole in the car under the airbox and then ran the pipe down to the front bar with a 90degree end on it for a bit of RAM air. It made quite a noticeable difference, even on the dyno, it went from 130rwkw to 140. |
|||
| Top | |
|||
| Whiteknight1 |
|
|||
|
Contemplating doing this....... Fiftyone, the water in your airbox, was this before or after the speed holes? Looks to be before.........but I just want to be sure.
_________________ Back in an E series! |
|||
| Top | |
|||
| fiftyone |
|
|||
|
before. i wouldn't be to conserned about it. after all there is a filter that will stop 99% of it getting through
_________________ ** For Sale ** {DESCRIPTION} |
|||
| Top | |
|||
| Falcs |
|
|||
|
just drill a small hole down the bottom to drain it out
_________________ -------- Falcs -------- |
|||
| Top | |
|||
| fiftyone |
|
|||
|
i drilled out the drain hole and put another in for good measure. i think the stuff in there is just condensation anyway
_________________ ** For Sale ** {DESCRIPTION} |
|||
| Top | |
|||
| theblackone |
|
|||
|
fityone - looks interesting.. bit slow on reading up on this....dont really look in this thread!
would this be affective for an ef xr6? i would assume so but not too sure if the corners are the same or not.
_________________ SIGNATURE REMOVED - REFER TO FORUM GUIDELINES! |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 2 guests |
