|
| 89.SVO |
|
|||
Age: 35 Posts: 3382 Joined: 11th Mar 2008 Ride: EA SVO, AU2, Toyota Crown Location: Bendigo |
is the hose that goes from the overflow bottle to the radiator on a NF 6 and 8 the same? my bro tried to get an aftermarket one for his NF 8 and they didn't list one
_________________ Daily driver: 2010 Toyota Crown hybrid 3.5L V6 hybrid. 254kw. |
|||
| Top | |
|||
| Papa Smurf |
|
||
|
WILDEB wrote: is the hose that goes from the overflow bottle to the radiator on a NF 6 and 8 the same? my bro tried to get an aftermarket one for his NF 8 and they didn't list one Yes they are the same, part number V890115 S750A $31.00. |
||
| Top | |
||
| alby-73 |
|
||
|
Papa Smurf wrote: alby-73 wrote: hey George just wondering if xg door hinges where still avail new? and $$$ if so or, do I have to go the repin mine route You should be able to use the XH hinges, they are still available but not cheap. The two upper ones EHC P22800 A $97.00 ea, 2 lower ones EHC P22806 A $97.00 ea. There are pins and bushes serviced for these hinges too, bushes are XD F22841 A x 8 $3.10 ea and Pins EHC P22840 A x 4 $7.50 ea, there are clips needed for the bottom of the pin but Ford in their wisdom has obsoleted them. To use these pins you would need to grind off the OLD pins and drive them out then you will be able to reassemble the hinge using the pins and find something to retain them like a circlip? George thanks george have the bushes already and have a set of xf hinges with circlips so may just repin/bush them so i am up for pins then thanks for the advice |
||
| Top | |
||
| dazza027 |
|
||
|
Papa Smurf, just wondering, when did the dovetail spoiler (the one that poked out behind the boot rather than sat above) become available on the early E series Falcons? Was it the EA S or the EB XR? And was it a genuine Ford part?
|
||
| Top | |
||
| jarae02 |
|
||
|
i am trying to take the ECU out of my AU1 having a few problems how is it done
|
||
| Top | |
||
| dazza027 |
|
||
|
Remove passenger side kick panel, remove phillips screw holding earth wire and retaining strap, gently pull ecu out far enough to get 10mm spanner onto retaining bolt on top of ecu which holds loom in, undo bolt until it undo's no more. Loom should now be free and ECU should be in your hand.
|
||
| Top | |
||
| TROYMAN |
|
||
|
nope... au ecu bracket needs to be drilled out as they have a security type bolt head that snaps off when fitted leaving what looks like a rivet...
|
||
| Top | |
||
| TROYMAN |
|
||
|
ya beat me to it ash!!!!!
|
||
| Top | |
||
| SLO247 |
|
||
|
Hi Papa Smurf, I know its a long shot, but does Ford still list anything towbar related for an NF Fairlane?
|
||
| Top | |
||
| phatba |
|
||
|
im guessing you cant buy fg fpv parts without an fpv vin, but any idea on the cost of each part needed to make a complete fg fpv top grille? cheers papa smurf
|
||
| Top | |
||
| dazza027 |
|
||
|
ashcook wrote: dazza027 wrote: remove phillips screw holding earth wire and retaining strap It'll be one of those security bolts that you need to grind the head off. Just replace it with a normal bolt when you put it back in. But be careful, its very easy to grind the earth wire too. Lol, my one was screwed. The old AU wasnt a virgin after all. |
||
| Top | |
||
| Papa Smurf |
|
||
|
dazza027 wrote: Papa Smurf, just wondering, when did the dovetail spoiler (the one that poked out behind the boot rather than sat above) become available on the early E series Falcons? Was it the EA S or the EB XR? And was it a genuine Ford part? That Lip Spoiler was started in EA and yes was genuine. |
||
| Top | |
||
| Papa Smurf |
|
||
|
SLO247 wrote: Hi Papa Smurf, I know its a long shot, but does Ford still list anything towbar related for an NF Fairlane? No, sorry matey. |
||
| Top | |
||
| Papa Smurf |
|
||
|
phatba wrote: im guessing you cant buy fg fpv parts without an fpv vin, but any idea on the cost of each part needed to make a complete fg fpv top grille? cheers papa smurf BGFP 8400 A Moulding $186.00 BG 8C104 C Top Grille Mould $110.00 BGFP 8142 C Grille Assy $867.81 805Y 8169 DA Grille Outer Surround $504.00 |
||
| Top | |
||
| low_ryda |
|
|||
|
hi papa smurf, what a sensational wealth of knowledge you bring that couldn't be matched by my local ford dealer... lol.
can you tell me if it's possible to buy the parts to make my AUIIxr6 into a '1 tonner' ? i'm under the impression it's a different brake master cylinder with an additional slave cylinder with an actuator arm...
_________________ Not to get technical, but according to chemistry alcohol is a solution. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 1 guest |
