|
| Papa Smurf |
|
||
|
{USERNAME} wrote: Hey Papa, is the rear window moulding for the box cars (EAF420A24A) still available? Sorry matey, gone the way of the DoDo. I would suggest trying a windscreen place, they usually supply moulds for when they fit screens. 
|
||
| Top | |
||
| low_ryda |
|
|||
|
For you're wealth of knowledge George I'm willing to wait
 however I'm talking about the floor carpet itself. I referred to it as a mould because it includes the kick panels etc. Alot of the after market carpets I've seen don't include the kick panels like the stock ones do. My carpet smells like dog & I need a new one... lol It peeves me that everything else is black apart from the carpet. Or perhaps they never made black in utes so it blends with the rear panelling ? Any help would be much appreciated as always.
_________________ Not to get technical, but according to chemistry alcohol is a solution. |
|||
| Top | |
|||
| Papa Smurf |
|
||
|
They DID make Black Carpets for the AU ute but they are obsolete.
BA utes are similar and maybe you could make one of them fit? at least you could then buy the plastic side panels and it wouldn't look so bad? The BA carpets are WAY too expensive to buy, $850.00 |
||
| Top | |
||
| SLO247 |
|
||
|
{USERNAME} wrote: For you're wealth of knowledge George I'm willing to wait however I'm talking about the floor carpet itself. I referred to it as a mould because it includes the kick panels etc. Alot of the after market carpets I've seen don't include the kick panels like the stock ones do. My carpet smells like dog & I need a new one... lol It peeves me that everything else is black apart from the carpet. Or perhaps they never made black in utes so it blends with the rear panelling ? Any help would be much appreciated as always. I'd track down a second hand genuine one in good condition, alternatively if yours is physically good get it steam cleaned or something? I haven't ever seen an aftermarket carpet that comes near matching a factory one, they are complete crap. Good luck! |
||
| Top | |
||
| low_ryda |
|
|||
|
Thats why I asked... I'm guessing they don't resell them ?
I'm just looking for an excuse to change to black from the 'charcoal' 
_________________ Not to get technical, but according to chemistry alcohol is a solution. |
|||
| Top | |
|||
| EDXR6-Poly |
|
|||
|
Hi George, whats a new genuine clutch cable worth for a ED manual (Im assuming there all the same) I6 with a T5, I think the part number on the old one I bought NOS was "EA-7K533-B"
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| Papa Smurf |
|
||
|
{USERNAME} wrote: Hi George, whats a new genuine clutch cable worth for a ED manual (Im assuming there all the same) I6 with a T5, I think the part number on the old one I bought NOS was "EA-7K533-B" The original cable is now obsolete but, I can't see why you couldn't use the EF/EL one? The EB/ED V8 uses the EL one so I am guessing the fitment to the clutch pedal is the same as the EF and from what I remember the EF/EL fitting to the lever is the same so? maybe it is a length issue? George |
||
| Top | |
||
| low_ryda |
|
|||
|
Thanks for that George, thats some expensive carpet! I'll keep an eye out.
_________________ Not to get technical, but according to chemistry alcohol is a solution. |
|||
| Top | |
|||
| EDXR6-Poly |
|
|||
|
I guess the EL one will be fine, whats the cost on that thanks george I maybe looking at buying 2
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
{USERNAME} wrote: As Loy_Ryda said, you CAN be lucky and find a dealer who will not charge you but they can charge up to $25.00 for it. You need to take the rego papers and a license to get the radio code normally and just giving them the 6FPAAA JGSW....... should suffice. I would strongly suggest you write the number either in the owners book or give it to your Missus or Mum?  well i went down to ford here, and they claim they have no access to the "system" and he would ring another dealership out of town and get me the code for free still waiting over a week later, and they reckon they "havnt got around to it"....... can i ring some other dealer and arrange it all over the phone?. i just want to get this stereo working 
|
||
| Top | |
||
| MMD |
|
||
|
can i get a price on a BA clutch master cylinder
thanks |
||
| Top | |
||
| Papa Smurf |
|
||
|
{USERNAME} wrote: can i get a price on a BA clutch master cylinder thanks M/Cyl BA 7A543 A $363.20 and the reservoir BA 7A542 A $52.26 |
||
| Top | |
||
| TerroristGHIA |
|
|||
|
Heyt George, Need a Z9 oil fiter for the 5.8, as well as a set of 8 BAXR6T plugs.
Will be out this morning to collect them if that suits Brett
_________________ The Terrorist ED Retired due to RUST. |
|||
| Top | |
|||
| knowsfords |
|
||
|
{USERNAME} wrote: {USERNAME} wrote: Hey Papa, is the rear window moulding for the box cars (EAF420A24A) still available? Sorry matey, gone the way of the DoDo. I would suggest trying a windscreen place, they usually supply moulds for when they fit screens. Dang, How about a 2.0L zetec crate motor? |
||
| Top | |
||
| Papa Smurf |
|
||
|
{USERNAME} wrote: Heyt George, Need a Z9 oil fiter for the 5.8, as well as a set of 8 BAXR6T plugs. Will be out this morning to collect them if that suits Brett Yes Brett and I have a BETTER filter, the D9AZ 6731 A American one
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 1 guest |
