The Key Blank is D101 76201 $47.50 and Oil Pressure is B367 18501 $35.90.
These are still available but we only have the OP switch. They are Mazda parts.

Ford never did but you could try http://www.egr.com.au/, they are the OEM for a lot of Ford accessories.

Hmm... I have a long list of questions and how I wish I could ask them all, but I'll limit myself. Lol

I have an AUII XR6 ute and want to change the front end from standard to a TS50 front, are the mounts the same/will the TS50 front interfear with anything?

Thanks

It should be a fairly straight swap. The guards are the same as is the engine bay. The only changes are the front bar, the headlights, bonnet and grille, the headlight wiring harness is different too.
You will even be able to use the front bar lower tray from your XR.

Hang on I might have gotten my description wrong, but I will need all that to go from standard to this? <a href="http://s1223.photobucket.com/albums/dd502/joshua_webb92/?action=view&current=b36135c9.jpg" target="_blank"><img src="http://i1223.photobucket.com/albums/dd502/joshua_webb92/b36135c9.jpg" border="0" alt="Photobucket Pictures, Images and Photos" /></a>

stuff genuine parts, 220$ for 1 lowsy fog light...
SOLUTION, fog light from ebay, comes with bracket n globe, 60$ n looks better than my other genuine 1, so will have to get 1 more now... Brent

Hey Papa Smurf, have you got a diagram of how the factory intercooler piping goes on a BA XR6 turbo? I bought a BA turbo 6 cross over and piping with intercooler but its missing 1 pipe just cant work out what one it is.

Its going on a AU ute with a turbo setup using the BA turbo gear, thus why I ask if you have the diagram to find out what one is missing out of my setup pease.

This is the best I can do for you.

How much is the pipe number 3? Turbo to intercooler pipe, Papa Smurf...

Hi George, just after pricing and availability on a few things.

-Auto Trans cooler kit for the AU XR6, whatever would have been fitted factory or by dealers? I want to fit one and bypass the radiator cooler and I figured factory would bolt straight up?
-One side repeater for the AU. The clear type. One is fogged up.
-Wiper arm for the AU?
-Starter motor for the AU 6. Is the BF one better?
-Lower rad hose and clamps for EL 4.0?
-I think I've asked this but never got an answer. The floor mat clips for the AU XR genuine mats?
-Can I buy one security wheel nut as fitted to my NL Concorde with the Tickford wheels? One is missing. I'm assuming I must buy a set.
-A long shot, but the boot side trim carpet for an NL Fairlane? LH side, and the rear speaker covers for the NL? Grey with Pioneer badges.
-The light above the drivers side sunvisor in the NL? Grey. Mine keeps falling out.

While I'm here too, I'd like to ask about the rear IRS mounts for the AU. I believe ours have been replaced but haven't had the extra washer fitted under the nut. Is this a part serviced by Ford? Or can you give me dimensions?

I'm also wondering if you can tell me what Ford recommends as diff oil for the 3.45 LSD in my NL Fairlane, and the 3.45 LSD In the AU IRS? The AU gives the odd clunk when cold if it changes gear during a corner and I'm told there is a known fix.

Thanks again!

These are so expensive, I am sure you could make one for MUCH less.
Part numbe is BAT 6F074 A $456.00

There is no cooler for the AU, some people used to fit the EF/EL one but it is now obsolete as well.
Side flasher, there are 2 of these, one is clear with an amvber insert ER 13K309 B $22.60 and the other is cleaar which uses an amber globe, AU3 13K309 A $19.00.
The starter motor is now serviced as the BA/BF type, BAF 11001 A $247.00.
Lower hose for the EF/EL EF 8286 BMC $28.90, clamps EF 8287 B $5.00 each.
Floor carpet retainers are obsolete.
As to the wheel nut, more than likely I could get one for you, if you have the key number?
Speaker covers are long obsolete as are the interior lights.
The IRS mount bush washers are long gone, unfortunately I cannot give you any dimmensions.
Diff oil is somthing Ford does not service, they give spec numbers only, SAE90EP.
BA/BF diffs had problems in the diff are with contamination in the oil but not AU, the noise was not a clunk but a whining noise.

HOLY M***** F****** gees I think I may just buy the pipe upgrade kit off ebay for $300 lol thanks anyway Papa Smurf mch appreaciated

Hey mate how much can you do a down stream o2 sensor for for my fg xr6 n/a?
Cheers Brad.

Hey Papa Smurf,
just wondering if you could help me out with a price for an AUII XR6 fuel regulator? Also just a few other little details on the side... is there another regulator that will work with the same rail (eg BA,etc)? and are the AUII XR injectors the same as standard AUII's?
thanks