|
phatal |
|
||
Age: 42 Posts: 517 Joined: 3rd Dec 2004 Ride: SZ Titanium & ZG Fairlane Location: Roxby Downs |
just a quick question. I have seen a lot of these threads about the I6 are the components used the same as what would be needed for an EL V8. Just that the pins on the ECU are different? In other words are the above diagrams correct for an EL V8 except for the ECU wiring? If so anyone know the correct pins?
_________________
|
||
Top | |
stomper |
|
|||
|
{USERNAME} wrote: just a quick question. I have seen a lot of these threads about the I6 are the components used the same as what would be needed for an EL V8. Just that the pins on the ECU are different? In other words are the above diagrams correct for an EL V8 except for the ECU wiring? If so anyone know the correct pins?
Im currently looking into this and i am sure that there MAY be different pin but over all i think its different got resistors. I hope to have the thing updated so that all EF/EL's V8's or i6's can go by the doco. I have also made someother improvements to the over all design with two LED's to tell you if the shift kit is either on or off. Currently this has been added to the bottom of the doco.
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
Top | |
stomper |
|
|||
|
Here is the a basic diagram for the LED warning. This is from the other thread but there was an error. They had the LED looped so basically both poles on the LED were going to the power.
{DESCRIPTION} You will be able to see power goes into the DPDT in the middle pole. Then you have the green and red LED's off the end poles. The other pin on the LEDs will connect to each other and go to negative or ground. I am planning taking the accessories power supply from the radio. That way the power is only on when the accessories are on. The LED wont drain enough power to drain the battery but still.
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
Top | |
twase |
|
|||
|
The LED's would need to be 12v ones standard ones will blow without a resistor in series..
_________________ BF Fairmont Ghia Series II update. |
|||
Top | |
stomper |
|
|||
|
{USERNAME} wrote: The LED's would need to be 12v ones standard ones will blow without a resistor in series..
You can not buy a LED that is 12V and will NO flash. So ill have to use a resistor on each of the LED's. Another note: Can someone please tell me what Pot i can use in replacement of the 5.6ohm resistor (e.g. Jaycar part number)? I went to jaycar to get all the parts and of course they didnt have a 5.6ohm 10 watt resistor. So ill go to the city jaycar today.
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
Top | |
twase |
|
|||
|
I am using a 3 pole 4 position rotary switch and individual resistors. I have not constructed it or tested it as yet.
_________________ BF Fairmont Ghia Series II update. |
|||
Top | |
twase |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: The LED's would need to be 12v ones standard ones will blow without a resistor in series.. You can not buy a LED that is 12V and will NO flash. . Why not? There are plenty that are panel mounted and 12v that don't flash.
_________________ BF Fairmont Ghia Series II update. |
|||
Top | |
stomper |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: {USERNAME} wrote: The LED's would need to be 12v ones standard ones will blow without a resistor in series.. You can not buy a LED that is 12V and will NO flash. . Why not? There are plenty that are panel mounted and 12v that don't flash. Can you give me a link to a 5mm RED and a 5mm GREEN LED that is 12v and dont flash? Myabe a jaycar cat number.
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
Top | |
twase |
|
|||
|
Farnell Part number 654 358 for red and 654 360 for green.
_________________ BF Fairmont Ghia Series II update. |
|||
Top | |
peyote |
|
||
|
jaycar
12v mini chrome bezel red cat number SL-2644 $2.55 green cat number SL-2645 $2.55 and the pot your looking for is 5 Ohm 15w cat number RP-3975 $9.95 Last edited by peyote on Thu Sep 21, 2006 1:54 pm, edited 1 time in total. |
||
Top | |
stomper |
|
|||
|
{USERNAME} wrote: jaycar
12v mini chrome bezel red cat number SL-2644 $2.55 green cat number SL-2645 $2.55 Not interested in a bezel BUT i think that a LED and a resistor is cheaper but really it doesnt matter. as long as it produces light.
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
Top | |
peyote |
|
||
|
you'll need a bezel to mount leds somewhere
|
||
Top | |
stomper |
|
|||
|
I have some things for mounting LED's into things but as i have jsut realised i didnt post a picture of what i have.
Ill try do that later. But like i said YOU CAN USE WHAT EVERY YOU WANT.
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
Top | |
fiftyone |
|
|||
|
look the pot up on the jaycar site. its the only 5 ohm pot they have. i think it needs a 1 ohm 10w to go with i think. just needs that little bit more
_________________ ** For Sale ** {DESCRIPTION} |
|||
Top | |
stomper |
|
|||
|
{USERNAME} wrote: look the pot up on the jaycar site. its the only 5 ohm pot they have. i think it needs a 1 ohm 10w to go with i think. just needs that little bit more
Cool. Just had a look and am still unsure. Have you got the part numbers for the two?
_________________ HOLDENS go like rockets. They fall apart in stages!!! |
|||
Top | |
Who is online |
---|
Users browsing this forum: No registered users and 1 guest |