|
| StevenBruzz |
|
|||
|
ik this is a noob question but can anyone do a right up on how to change el springs asap as i have oppurtunity to do it today i did have sumone that was guna help but that feel through
has standard springs and shocks putting lowerd springs in with standards shocks - see how they go then get it wheel aligned  atm its out 2mm pulling left
|
|||
| Top | |
|||
| kickn_it |
|
||
|
How low are you goin, sports low or super low cause if you go too low with standard shocks you'll be pulling them out very shortly due to f******g them up.
Have a search around mate in the forums as someone would have put them up for sure. There are also ford manuals you can download from this ite which will cover how to change them over. The rears are very straight forward but make sure you are very careful with the fronts, cause if you undo the top nut without spring compressors be prepared to get a nasty whack from the release of tension holding the spring onto the strut. You can get to the rears shockers by removing the small part of the back seat near each rear door. They just pull off as they are just clipped in. Hope that gives you some direction. If in doubt ask. Cheers Joel
_________________
|
||
| Top | |
||
| BenJ |
|
||
|
Step 1.
Drive your car to an auto shop. Step 2. BUY A WORKSHOP MANUAL!!!!!!! Step 3. Read the Workshop Manual. Step 4. Get under your car and get to work. We are not going to type up a couple of pages telling you how to do anything when the experts have already done it. I learnt how to do all of my mods, by doing a bit of reading, 'Gregorys' for me, and then getting grubby having a go. Good Luck Cheers BenJ
_________________ {DESCRIPTION} - Current Ride |
||
| Top | |
||
| BEAR80 |
|
|||
Age: 44 Posts: 683 Joined: 4th Mar 2010 Ride: BF Fairmont Ghia & TS Magna Location: central coast |
{USERNAME} wrote: Step 1. Drive your car to an auto shop. Step 2. BUY A WORKSHOP MANUAL!!!!!!! Step 3. Read the Workshop Manual. Step 4. Get under your car and get to work. We are not going to type up a couple of pages telling you how to do anything when the experts have already done it. I learnt how to do all of my mods, by doing a bit of reading, 'Gregorys' for me, and then getting grubby having a go. Good Luck Cheers BenJ you forgot something ben, pay someone else to do it..... in other word RTFM LOL |
|||
| Top | |
|||
| Troy |
|
||
|
pretty crazy being on stock springs/shocks when you got 562rwkw lol.
definitely buy a workshop manual! will help a s**t load |
||
| Top | |
||
| StevenBruzz |
|
|||
|
Haha yea i was jus playn with dyno sheet when bored
|
|||
| Top | |
|||
| revcore |
|
|||
|
On an added note from what everyone else has mentioned, If you haven't already got them on your car I'd recommend a camber caster kit as this will allow you to get perfect alignment of your front wheels.
_________________
|
|||
| Top | |
|||
| StevenBruzz |
|
|||
|
Finaly a smart intellegent post
|
|||
| Top | |
|||
| bry40l |
|
|||
|
the backs are straight forward as mentioned before, if your using standard shocks dont go lower than "low" springs (xr height) because 1 it will be uncomfortable to drive and 2 the shocks will eventually fail from bottoming out
_________________ BF XR6 |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 38 guests |
