Fordmods Logo

Clunking front fix 

 

Page 1 of 1 [ 5 posts ] 

 
 Post subject: Clunking front fix
Posted: Wed Sep 07, 2005 9:23 pm 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 2705

Joined: 6th Nov 2004

Gallery: 11 images

Ride: 2009 FG XR6 Sedan

Location: Melbourne
VIC, Australia

If there are any people with an annoying clunk at slower speeds over small bumps mainly on the passenger side i found the problem.
If the tie rod end is ok it is more than likely to be the rack end (joint inside the steering rack boot)
To diagnose it cut the cable tie on the inner of the boot and peel it back. with the car on ramps (wheels not floating) start engine and have some one turn the steering wheel back and forth. if its worn you will be able to see movement in the joint.

Replaced both today and adjusted toe in and only took about 1 1/2 hrs.
Also if the joint is badly worn it will cause toe out resulting in the outer shoulders on the tyre to scuff.
Top
 Profile  
 
 
 Post subject: Re: Clunking front fix
Posted: Thu Sep 08, 2005 5:05 am 
Getting Side Ways
Offline
User avatar

Age: 42

Posts: 492

Joined: 8th Nov 2004

Gallery: 2 images

Ride: EF Fairmont Wagon, ph34r!

Location: Northam
WA, Australia

{USERNAME} wrote:
resulting in the outer shoulders on the tyre to scuff.


Interesting...

I've noticed the clunking in my front end for a while now but after losing a tyre on the rear (which used to be on the front) I noticed that there was more wear on the outer edges than in the middle. The guy I took it to said it was due to running them under inflated which is certainly a possibility - I don't keep as nearly as watchful an eye on my tyre pressure as I should - but this seems to make sense as well. I'll make sure that I have the tie rod ends checked when I finally get the dough together to replace the back tyres and have the alignment reexamined.

 

_________________

Team Argon Silver

Top
 Profile  
 
 
Posted: Thu Sep 08, 2005 5:15 am 
Getting Side Ways
Offline
User avatar

Age: 50

Posts: 2705

Joined: 6th Nov 2004

Gallery: 11 images

Ride: 2009 FG XR6 Sedan

Location: Melbourne
VIC, Australia

Too lower inflation causes both shoulders to wear and too much causes the inner to wear.
The tie rods are on the outer and the rack ends are on inner (inner tie rods.
The reason the outer shoulder wears with toe out is because of the caster angle, as the tie rods and rack ends wear the wheels pull back giving them toe out.
The clunking may not only be from the tie rods but a number of things like worn shocks, rack, steering shaft or wheel bearings.
It took me a while to find this so i thought id share it.
Top
 Profile  
 
 
Posted: Thu Sep 08, 2005 11:17 am 
Getting Side Ways
Offline
User avatar

Age: 54

Posts: 1826

Joined: 6th Nov 2004

Gallery: 3 images

Ride: 1997 Falcon EL Gli/Sleeper

Location: Bayside, Brisbane
QLD, Australia

I only get the,"Clunk" sound when I am reversing intially or turning a Tight Corner on a Hill at about 30km/h all other times I never hear it?

 

_________________

" In life their is never an Obligation just an Opportunity to..Own an awesome 1970 Ford Mach 1 Mustang! "

Top
 Profile  
 
 
Posted: Thu Sep 08, 2005 1:07 pm 
Getting Side Ways
Offline
User avatar

Age: 38

Posts: 11105

Joined: 15th Nov 2004

Ride: No Fords current

Location: Hobart
TAS, Australia

When I go over a speed bump or am slightly harder on the brakes that normal or something like that (i think when the front end of my car dips down a bit) i often get a clunk. Sound like suspension to me.
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 5 posts ] 

Who is online

Users browsing this forum: No registered users and 36 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Tue Dec 24, 2024 3:56 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names