|
| SWC |
|
||
|
|
||
| Top | |
||
| Rick's EF Fairmont Wagon |
|
||
|
Who stocks brembo discs? what price? availability?
_________________ BF3 Egas XT Wagon |
||
| Top | |
||
| SWC |
|
||
|
Check the following suppliers;
NSW; http://www.racebrakessydney.com.au/ NSW, VIC, QLD, ACT; http://www.vsport.com.au/ Hope these help |
||
| Top | |
||
| Rick's EF Fairmont Wagon |
|
||
|
Thanks,
I will see what they cost.
_________________ BF3 Egas XT Wagon |
||
| Top | |
||
| mattymc |
|
||
|
Just wondering what peoples opinions are on DBA and RDA slotted rotors. I am looking at one of these brands and wondered how they are quality wise and price. I know the RDA'S are cheaper but did not want to get a set of poor quality rotors.
Anyone know the best place to get DBA and RDA rotors and prices? I guess ebay would be good for the RDA rotors but has anyone have dealings with a particular seller that was good. Cheers Matthew |
||
| Top | |
||
| FAST-XR |
|
|||
|
I have used rda slotted and dba slotted rotors, didnt have any problems with either, the only thing i liked about the dba rotors is that they had a painted hub, so they didnt rust and turn orange.....
_________________ 07 BF MKII XR6T |
|||
| Top | |
|||
| kwaussiekid |
|
||
|
I fitted DBAs slotted, to my EB and they made a world of difference.Apparently the crossed drilled variety have had issues with breaking down.But if you intend fitting these, then also fit braided lines,for the best results.I purchased my stuff from Bursons.
_________________ The older I get the better I was! |
||
| Top | |
||
| mattymc |
|
||
|
Thanks guys. I am not looking at drilled rotors just the slotted as its only my street car. I like the idea of dba's painted hubs. Its a bit of a pain having to paint hubs and if the prices are similar I think ill give the dbas a go. But good to know that they are both good rotors.
|
||
| Top | |
||
| EDXR6-Poly |
|
|||
|
Will EA-ED slotted front rotors fit a XF? or are they completely different?
_________________ AU2 engine with Hoppers head/cam performance package & spool rods / CP pistons ,Snort 1200 plenum, T56 Manual & Billet short shifter, Front & Rear Slotted rotors, Pedders lowered suspension, LSD and tuned with EMS stinger 4424 347rwkw THE ED XR6 IS BOOSTED |
|||
| Top | |
|||
| timn2087 |
|
||
|
I have read through the thread, and I am still not sure if I should go with DBA slotted or cross drilled? It's for my NF Fairlane. And is the general consensus to go for EBC green stuff pads? BTW, how much would Brembo rotors set me back?
_________________ '95 NF Fairlane. Lowered, EL GT rims, Car Bra, Pacemakers, 2.5" straight through exhaust, Hiflo cat, 5" intake, DBA slotted rotors, EBC Green Stuff pads, Top gun Max300 leads & NGK Iridium IX plugs |
||
| Top | |
||
| mix-six |
|
||
|
hey guys. need some help... I wasn't too sure where to put this but here it is.
The old man has a Bf xr6 and he is having massive trouble with his brakes. rotors warping and just not lasting at all. he has been talking to race brakes and they say he should go for some brembos... just the calipers... 4 or 6 pot... here is the question if he buys the brembos will he need 18's 19's or 20's??? or can he just stick to the 17's
_________________ MIX68U Now living in the ACT! |
||
| Top | |
||
| low_ryda |
|
|||
|
thought this might be the best place to ask if anyone knows who makes these rotors ? .........
Attachment: rotor.jpg [ 36.95 KiB | Viewed 507 times ] came off an auII xr, I thought all ford rotors had the single fin vents ? also standard ford rotors usually have numbers cast into them. These have nothing at all on them, thought someone might be able to tell me who makes them. Attachment: rotor2.jpg [ 40.09 KiB | Viewed 468 times ]
_________________ Not to get technical, but according to chemistry alcohol is a solution. |
|||
| Top | |
|||
| Benny D |
|
|||
|
{USERNAME} wrote: hey guys. need some help... I wasn't too sure where to put this but here it is. The old man has a Bf xr6 and he is having massive trouble with his brakes. rotors warping and just not lasting at all. he has been talking to race brakes and they say he should go for some brembos... just the calipers... 4 or 6 pot... here is the question if he buys the brembos will he need 18's 19's or 20's??? or can he just stick to the 17's im preety sure if you hav brembos you need 18+"s
_________________ BA XT V8. Ice Mint. 18" Speedys. XR6T LSD. Full Pacemaker twin 2 1/2inch Stainless Steel system. Custom CAI. Black XR interior with white trimming. Powerbond underdrive kit 25%. |
|||
| Top | |
|||
| TROYMAN |
|
||
|
{USERNAME} wrote: thought this might be the best place to ask if anyone knows who makes these rotors ? ......... Attachment: rotor.jpg came off an auII xr, I thought all ford rotors had the single fin vents ? also standard ford rotors usually have numbers cast into them. These have nothing at all on them, thought someone might be able to tell me who makes them. Attachment: rotor2.jpg im pretty sure they are dba rotors?? the kangaroo paw design.. http://www.youtube.com/watch?v=8PzWFn6l ... dded#at=12 |
||
| Top | |
||
| low_ryda |
|
|||
|
exactly what I was thinking troyman cheers. wasn't sure if they stamped anything into the rotor or not. Thanks mate.
_________________ Not to get technical, but according to chemistry alcohol is a solution. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 42 guests |
)
