Diff Questions - LSD Options - www.fordmods.com

Home » Forums » Fordmods Tech » Gearbox, Suspension, Brake & Driveline Workshop

Diff Questions - LSD Options

Page 1 of 1 [ 8 posts ]

Post New Topic Post Reply

Previous topic Next topic

BenJ

Post subject: Diff Questions - LSD Options

Posted: Mon Jul 09, 2007 6:02 pm

Getting Side Ways

Offline

Posts: 5503

Joined: 20th May 2005

Gallery: 11 images

Ride: EB1 Fairmont Ghia T5 Wagon

Location: Seven Hills, Sydney
NSW, Australia

Hi all

Looking for some budget options to hook the EB up with an LSD.

Q1. Will a diff (disc to disc) from an NA Fairlane bolt into an EB11?

Q2. Would and LSD centre from and ED 2.77 ratio be able to be swapped into an EB11 3.23 ss housing?

Any other sensible suggestions?

BenJ

_________________

BenJ's EB T5 DOHC Ghia Wagon - Current Ride
BenJ's EB GL Sedan - Previous Ride
My respect and thanks go to - snap0964, Paulmac, SWC and MRE-50L

Top

Profile

twase

Posted: Mon Jul 09, 2007 8:25 pm

Getting Side Ways

Offline

Posts: 2644

Joined: 6th Nov 2004

Gallery: 8 images

Ride: 2007

Location: Mount Annan
NSW, Australia

Q1, not unless you change the pinion flange and use the EA lower control arms.
Q2, I think this would be more viable then option 1
The diff center is larger for a LSD over a non LSD, but I think it may fit, you will need to setup the diff preloads and backlash again.

_________________

BF Fairmont Ghia Series II update.
GQ XR6T ghia patrol.

,======o00o
//__|__|_,\_____\,___
|_/--\'_|'__|_/--\_[]IIII[]
_( o ) )_____( o ) )=o=) )__

Top

Profile

BenJ

Posted: Tue Jul 10, 2007 6:37 pm

Getting Side Ways

Offline

Posts: 5503

Joined: 20th May 2005

Gallery: 11 images

Ride: EB1 Fairmont Ghia T5 Wagon

Location: Seven Hills, Sydney
NSW, Australia

Thanks for the reply.

Can I use a tail shaft from an EA or EB1 if I use the NA diff? I am presuming the spline on the gearbox end will be the same.

BenJ

_________________

BenJ's EB T5 DOHC Ghia Wagon - Current Ride
BenJ's EB GL Sedan - Previous Ride
My respect and thanks go to - snap0964, Paulmac, SWC and MRE-50L

Top

Profile

twase

Posted: Tue Jul 10, 2007 8:54 pm

Getting Side Ways

Offline

Posts: 2644

Joined: 6th Nov 2004

Gallery: 8 images

Ride: 2007

Location: Mount Annan
NSW, Australia

You can but you are better of swapping the pinion flange over.

_________________

BF Fairmont Ghia Series II update.
GQ XR6T ghia patrol.

,======o00o
//__|__|_,\_____\,___
|_/--\'_|'__|_/--\_[]IIII[]
_( o ) )_____( o ) )=o=) )__

Top

Profile

BenJ

Posted: Tue Jul 10, 2007 11:46 pm

Getting Side Ways

Offline

Posts: 5503

Joined: 20th May 2005

Gallery: 11 images

Ride: EB1 Fairmont Ghia T5 Wagon

Location: Seven Hills, Sydney
NSW, Australia

So that can be done without dimantling the diff?

I will check the Manual.

BenJ

_________________

BenJ's EB T5 DOHC Ghia Wagon - Current Ride
BenJ's EB GL Sedan - Previous Ride
My respect and thanks go to - snap0964, Paulmac, SWC and MRE-50L

Top

Profile

twase

Posted: Wed Jul 11, 2007 8:28 am

Getting Side Ways

Offline

Posts: 2644

Joined: 6th Nov 2004

Gallery: 8 images

Ride: 2007

Location: Mount Annan
NSW, Australia

Sure can, you are best of doing it in the car with the wheels on so you can undo the nut but it can be done otside. The preload on the pinion is done with a collapsible spacer so as long as you tighten it back up to the same tension it should retain the original preload. Tip: Change the seal while its out.

_________________

BF Fairmont Ghia Series II update.
GQ XR6T ghia patrol.

,======o00o
//__|__|_,\_____\,___
|_/--\'_|'__|_/--\_[]IIII[]
_( o ) )_____( o ) )=o=) )__

Top

Profile

Dansedgli

Posted: Wed Jul 11, 2007 9:18 am

Getting Side Ways

Offline

Age: 40

Posts: 3405

Joined: 7th Feb 2005

Ride: AU2 Ute

Location: melbourne
VIC, Australia

Why is he better off changing the pinion flange rather than changing the tailshaft?

It would be an easier job to change tailshafts wouldnt it?

Top

Profile

twase

Posted: Wed Jul 11, 2007 10:57 am

Getting Side Ways

Offline

Posts: 2644

Joined: 6th Nov 2004

Gallery: 8 images

Ride: 2007

Location: Mount Annan
NSW, Australia

Easier yes, in my experience better no. The later model rear uni design is much better. Having been on the end of a tailshaft uni failure at high speed I hate the ealier design.

_________________

BF Fairmont Ghia Series II update.
GQ XR6T ghia patrol.

,======o00o
//__|__|_,\_____\,___
|_/--\'_|'__|_/--\_[]IIII[]
_( o ) )_____( o ) )=o=) )__

Top

Profile

Post New Topic Reply

Page 1 of 1 [ 8 posts ]

Jump to:

Home » Forums » Fordmods Tech » Gearbox, Suspension, Brake & Driveline Workshop

Who is online
Users browsing this forum: No registered users and 95 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

It is currently Sat Nov 16, 2024 1:56 am

All times are UTC + 11 hours