|
| alfy |
|
|||
|
Afternoon all,
been driving the Fairlane around all day since converting it last night and it seems that it has a rather large shudder on take off. Could the cause be the fact that we completely forgot to have the flywheel machined? Or does something else cause it? Chris
_________________ 2021 V6 Manual Amarok - 245kw/750nm - many goodies |
|||
| Top | |
|||
| Bourbon Ute |
|
||
|
If the flywheel is bad enough, yes it can cause shudder.
|
||
| Top | |
||
| alfy |
|
|||
|
hmmm. screw pulling it all apart again, i'll put up with it till I get a new clutch
_________________ 2021 V6 Manual Amarok - 245kw/750nm - many goodies |
|||
| Top | |
|||
| cjh |
|
|||
|
Check your engine & g'box mounts too.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| tearlejc |
|
||
|
did you look at the flywheel face condition at all when it was apart? Last time I did a new clutch I was in a hurry, didn't have any other transport, etc etc - looked at the flywheel and thought oh bugger it I won't get it resurfaced, gave it a going over with wet/dry 600 grit paper - I got a little bit of shudder when cold for a week or so and thought oh bugger, stuffed that up...and thought same as you, I'll wait until I need a new clutch - car's going, can't be stuffed pulling it all out etc - after a month or so it all bedded itself in and it was all good. That was nearly 5 years ago now, still on that same clutch, everythings fine....
_________________ 351 4V XB Coupe running LPG |
||
| Top | |
||
| alfy |
|
|||
|
tearlejc wrote: did you look at the flywheel face condition at all when it was apart? Last time I did a new clutch I was in a hurry, didn't have any other transport, etc etc - looked at the flywheel and thought oh bugger it I won't get it resurfaced, gave it a going over with wet/dry 600 grit paper - I got a little bit of shudder when cold for a week or so and thought oh bugger, stuffed that up...and thought same as you, I'll wait until I need a new clutch - car's going, can't be stuffed pulling it all out etc - after a month or so it all bedded itself in and it was all good. That was nearly 5 years ago now, still on that same clutch, everythings fine.... hmm, alrighty i'll keep driving it around for a while and see if it fixes itself. cheers for the info guys!
_________________ 2021 V6 Manual Amarok - 245kw/750nm - many goodies |
|||
| Top | |
|||
| low_ryda |
|
|||
|
a bit of oil in there on assembly can do that to.. did you burn the surfaces clean? They are pretty bulletproof. I mixed and matched a second hand clutch plate with a different second hand pressure plate onto a second hand flywheel and I'm surprised it's still going strong, not that I recommend that lol.
My old mans cruiser leaks oil from the rear main when it sits for a long time and causes shudder untill it burns off.
_________________ Not to get technical, but according to chemistry alcohol is a solution. |
|||
| Top | |
|||
| alfy |
|
|||
|
low_ryda wrote: a bit of oil in there on assembly can do that to.. did you burn the surfaces clean? They are pretty bulletproof. I mixed and matched a second hand clutch plate with a different second hand pressure plate onto a second hand flywheel and I'm surprised it's still going strong, not that I recommend that lol. My old mans cruiser leaks oil from the rear main when it sits for a long time and causes shudder untill it burns off. ah that could be it the donor car pretty much had no rear main seal so its probably fairly soaked lol
_________________ 2021 V6 Manual Amarok - 245kw/750nm - many goodies |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 45 guests |
