|
| ef_falcon_95 |
|
|||
|
Au 2 have a hole in the top for a shim
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
bugger i bought the wrong ones, i take it you cant use the BA ones ?
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
I can , as they have the same mounting points as AU . Are they a sliding caliper ?
Took the car for a drive up the pass , through kangaroo valley and came out at nowra . Went great except for when I went around a down hill tight corner fast and braked hard. The rotor rubbed on the caliper anchor plate for a minute , then when I braked it went away then came back again . Lasted for about 2 minutes . All good now . It only ever happens going down a tight corner , the tyre scrubs on the guard followed by the rotor making a noise . Then its back to normal. I've gone around tight flat corners while braking hard and its fine. Must be that much force pushing the hub in , it only rubs on the inside of the rotor which explains the force pushing it in and only on left hand turns. I'm not going to worry too much I never go down steep descents often but if I do I'll take it easy around very tight corners . Like a hair pin .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
what do you mean by sliding caliper?
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
The caliper has 2 pins going into the bracket which slide in and out
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
yeah i think they do , im gonna buy matts au 2 calipers ,
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
do you know if the ba caliper bracket is the same as the au2 ones ?
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
I don't think it's the same
_________________ El XR6 Turbo |
|||
| Top | |
|||
| TURBO_GHIA |
|
|||
|
arh ok no worries
_________________ HMMMM BOOST !!!
|
|||
| Top | |
|||
| kick_ass_ford |
|
|||
|
quick question if you can make the up rights and that for 350 what else will i need on my end. discs calipers pads brake lines??
_________________ EF XR6 |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
You will need a bracket or I can do that for extra $100 .
Then you'll need Bearings $30 Brake lines $200 Pads $50 Hub rings $25 Rotors $200 Calipers $40 +$50 for rebuild kit Ball joints $45 Bearings and ball joints are optional but best to get new ones depending on condition.
_________________ El XR6 Turbo |
|||
| Top | |
|||
| kick_ass_ford |
|
|||
|
that not bad ill have to hit u up soon.
_________________ EF XR6 |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
Your getting it all for under $1000 and the kit has a good chance of passing NSW engineering .
_________________ El XR6 Turbo |
|||
| Top | |
|||
| kick_ass_ford |
|
|||
|
i live in vic anyways
_________________ EF XR6 |
|||
| Top | |
|||
| ef_falcon_95 |
|
|||
|
That's ok
_________________ El XR6 Turbo |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 25 guests |
