|
| idlizn |
|
||
|
I'm changing the brake pads on my '92 Eb fairmont ,
front pads ,no worries ,take the old pads off put the g clamp on to squash that cylinder back down,new pads on, back together all good. BUT , then the back and then a problem.they came off ok but I can't compress that cyclinder back to get the new pads in ? yes I took the handbrake off, but try as i like the G clamp will not compress ,it's quite bent now but I still cant get the new pads on ,, any help would be sweet .. thanks in adv. Simon Mc.
_________________ 5.0 1992 EB mont |
||
| Top | |
||
| cjh |
|
|||
|
Easiest way, get a workshop manual and read it, it'll be quicker than trying to explain it.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| PIMP_LTD |
|
||
|
Your caliper is possibly seized. I ad this problem a while ago, my calpiers were partly siezed, and i had to pull them apart and put a kit through them.
However its easier to just go to the wrecker and get another caliper.
_________________ Commodore australia's favorite car??? What a load of s**t |
||
| Top | |
||
| racedirector |
|
|||
Age: 63 Posts: 1584 Joined: 20th Mar 2005 Ride: EDL Fairmont Wagon/AU XR8 Ghia Location: Riverstone |
The rears don't just push it, they have to be wound in like a bolt. You can get a tool from Supercheap to do the job.
_________________ =1994 ED Wagon GLi body/EL Fairmont spec with *ALL* EL running gear.= |
|||
| Top | |
|||
| phantom |
|
|||
|
You have to screw the rear pistons in on Ea-ED
|
|||
| Top | |
|||
| idlizn |
|
||
|
thanks for all the replies (except the workshop manual one )
I'll go screw her then 
_________________ 5.0 1992 EB mont |
||
| Top | |
||
| PIMP_LTD |
|
||
|
LOL, i thought you were talking bout the fronts, haha.
Yeah they screw in on back.
_________________ Commodore australia's favorite car??? What a load of s**t |
||
| Top | |
||
| cjh |
|
|||
|
idlizn wrote: thanks for all the replies (except the workshop manual one )
I'll go screw her then There is more to it than just screwing it in, there's resetting the park brake too.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| Private9 |
|
|||
|
Glad I found this thread!
Being the gump I am, I spent about half an hour today trying to push the piston back in my rear caliper with a g clamp. Hope I didn't stuff it!!! When you guys say just screw the piston back in, how exactly do you do it? Sorry for the dumb Q by the way! |
|||
| Top | |
|||
| cjh |
|
|||
|
Private9 wrote: Glad I found this thread!
Being the gump I am, I spent about half an hour today trying to push the piston back in my rear caliper with a g clamp. Hope I didn't stuff it!!! When you guys say just screw the piston back in, how exactly do you do it? Sorry for the dumb Q by the way! You need a tool to screw in the piston. Or you can do it the harder way of winding in the handbrake actuating shaft with a 13mm open end spanner and at the same time push the piston back in with a large pair of multi-grips. Remember to check the caliper slides for ease of movement and lube the rubber washer on the back of the caliper. Use silicone grease to lube those points.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| Private9 |
|
|||
|
cjh wrote: Private9 wrote: Glad I found this thread! Being the gump I am, I spent about half an hour today trying to push the piston back in my rear caliper with a g clamp. Hope I didn't stuff it!!! When you guys say just screw the piston back in, how exactly do you do it? Sorry for the dumb Q by the way! You need a tool to screw in the piston. Or you can do it the harder way of winding in the handbrake actuating shaft with a 13mm open end spanner and at the same time push the piston back in with a large pair of multi-grips. Remember to check the caliper slides for ease of movement and lube the rubber washer on the back of the caliper. Use silicone grease to lube those points. Thanks mate. Could I use a flatblade and just screw the slot in the piston? |
|||
| Top | |
|||
| TwinturboBMX |
|
|||
|
I normally use a rather large flatblade, works a charm, saves money on 'the' tool.
_________________ 17" Tezza Steelies, King F**king lows, pedders sports ryders, 2.5" cat back exhaust, pacemaker extractors, T5 manual
|
|||
| Top | |
|||
| cjh |
|
|||
|
Private9 wrote: cjh wrote: Private9 wrote: Glad I found this thread! Being the gump I am, I spent about half an hour today trying to push the piston back in my rear caliper with a g clamp. Hope I didn't stuff it!!! When you guys say just screw the piston back in, how exactly do you do it? Sorry for the dumb Q by the way! You need a tool to screw in the piston. Or you can do it the harder way of winding in the handbrake actuating shaft with a 13mm open end spanner and at the same time push the piston back in with a large pair of multi-grips. Remember to check the caliper slides for ease of movement and lube the rubber washer on the back of the caliper. Use silicone grease to lube those points. Thanks mate. Could I use a flatblade and just screw the slot in the piston? That might depend on how hard the piston is to turn.
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 140 guests |
