|
| Nath_ |
|
||
Age: 37 Posts: 542 Joined: 25th Jun 2006 Ride: BA XR6 5 speed. 96 Ford Fairmont Location: Darwin |
Hi guys I've been trying to remove my tail shaft from my EF gearbox but cant figure out how to.
I cant see how I can get a spanner into it (the other ends easy enough!). Can anyone help me out here. Is it easier just to disconnect the back end of the tail shaft and drag it out with the old gearbox then remove it? It sounds like allot of stuffing around though.. Thanks for any help. Cheers, Nathan |
||
| Top | |
||
| Nath_ |
|
||
Age: 37 Posts: 542 Joined: 25th Jun 2006 Ride: BA XR6 5 speed. 96 Ford Fairmont Location: Darwin |
dumb a***!
Just figured out that the tail shaft slides out of the box... |
||
| Top | |
||
| glenneaux |
|
||
|
yep you do suck!
|
||
| Top | |
||
| The Dog |
|
|||
|
 He he just done this today...hehe woulda posted something similar... 
_________________ You'll ride a black tornado across the western sky
|
|||
| Top | |
|||
| glenneaux |
|
||
|
hehe yeah its a bit deceiving.
Tailshaft slides out, just watch out for rogue tranny fluid! |
||
| Top | |
||
| Nath_ |
|
||
Age: 37 Posts: 542 Joined: 25th Jun 2006 Ride: BA XR6 5 speed. 96 Ford Fairmont Location: Darwin |
Fare out guys those bolts are hell tight! I cant manage to loosen them without the spanners slipping. I'm going to repco soon to pick up a single hex socket and give it a fair go then. There just to tight...
Cheers, Nathan |
||
| Top | |
||
| glenneaux |
|
||
|
{USERNAME} wrote: Fare out guys those bolts are hell tight! I cant manage to loosen them without the spanners slipping. I'm going to repco soon to pick up a single hex socket and give it a fair go then. There just to tight...
Cheers, Nathan What bolts? Driveshaft slides out of the gearbox and has 4 bolts on the flange at the diff.. 2 decent ring spanners will make short work of that.. |
||
| Top | |
||
| nannas_ed |
|
|||
|
ha ha yep those diff flange bolts are a prick to get of but then again youd be worried if they wernt tight :S
_________________
|
|||
| Top | |
|||
| phongus |
|
|||
|
{USERNAME} wrote: ha ha yep those diff flange bolts are a prick to get of but then again youd be worried if they wernt tight :S
...they have thread locker on them that's why. make sure you put some thread locker on when you put the tailshaft back in...well it is recommended. phong =P~
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Nath_ |
|
||
Age: 37 Posts: 542 Joined: 25th Jun 2006 Ride: BA XR6 5 speed. 96 Ford Fairmont Location: Darwin |
Pretty sure I took the easy way out and just got an auto service centre to do the dirty work for me.
I had no idea it would be so cheap. There in and out in less than a day... Problem solved... Cheers, Nathan |
||
| Top | |
||
| Shum's EL |
|
|||
|
{USERNAME} wrote: {USERNAME} wrote: Fare out guys those bolts are hell tight! I cant manage to loosen them without the spanners slipping. I'm going to repco soon to pick up a single hex socket and give it a fair go then. There just to tight... Cheers, Nathan What bolts? Driveshaft slides out of the gearbox and has 4 bolts on the flange at the diff.. 2 decent ring spanners will make short work of that.. yeah make sure you use RING spanners.. open enders always seem to round bolts and cause skin loss on knuckles haha |
|||
| Top | |
|||
| joolz |
|
|||
|
From memory the diff flange bolts are 18 and 15mm. Make sure you mark the original position of the driveshaft so as the system balance is retained when shaft refitted.
|
|||
| Top | |
|||
| GTBob |
|
|||
|
That sound like a good idea in theory but if the tailshaft is balanced it can be bolted in either way and if it isn't balanced it will vibrate no matter where you put it
_________________ Rotten Old Revhead!!! XW GTHO + EF ex cop car (exractors 2.5 cat back zorst !6" Simmons K&N +airbox mods Lowered with Bilstein shocks+Whiteline Bars NEXT THING Swap HO for GTP or Ferrari! |
|||
| Top | |
|||
| joolz |
|
|||
|
To further explain the yellow dots on the driveshaft and diff flange. The dots on the shafts represent the lighter side after balancing and the dot on the diff flange is the heavier side after balancing, the trans also has a dot on the output shaft but washes off. The reason why there is a lighter and heavier side after balancing is simply due to mass production which makes it impossible to get a zero imbalance. If it was possible you would never have to get new tyres balanced.
|
|||
| Top | |
|||
| FordFairmont |
|
||
Posts: 6113 Joined: 8th May 2007 |
Those bolts are definitely a pain in the a***. Breaker bar or another spanner on the end of it helps
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 60 guests |
