|
| danc666 |
|
||
|
Has anyone done this for a ba??? can you tel me which pins to use please?
|
||
| Top | |
||
| moodyblues |
|
||
|
ey silly question is this the same for EB (series 2 fairmont)?
and does any one no wat colour the 2 wires are that come from the respective pins as i couldnt see number any where!!! Thanks
_________________ mal |
||
| Top | |
||
| Paulmac |
|
||
|
Mal,
Just a suggestion, read through the thread until you find someone with an EB2-ED that's done it. Click on the 'PM' button in that post and ask them directly. Cheers, Paul
_________________ What goes around, comes around. |
||
| Top | |
||
| moodyblues |
|
||
|
Yeah i know i tried to read thru it as much as i could and could only find one instance where i believe even the person with the car and EB mont ser.1 wasnt sure wat was going on with his car TCM and such. if there is any one here who has done it to the EB ser.2 any help would be much appreciated@!
_________________ mal |
||
| Top | |
||
| Paulmac |
|
||
|
PM 'BenJ', he may be able to help you out, use the search button up the top.
Paul
_________________ What goes around, comes around. |
||
| Top | |
||
| xfpaul |
|
||
|
any problems after the mod , please report even the smallest ????
_________________ NC2 Fairlane AU2 Intech 4.0 Wolf V500 ECU Accel 500cc Injectors Eaton M90 Blower MPx Porting 75mm Mustang TB Intercooler Holley 255lph EL XR6 Rear End 3.45 LSD Duel Fuel lots more. |
||
| Top | |
||
| BenJ |
|
||
|
I broke an Engine Mount under full throttle first to second. Chirped the wheels nicely.
BenJ
_________________ {DESCRIPTION} - Current Ride |
||
| Top | |
||
| Paulmac |
|
||
|
Ben, Ben...with a 400k klms engine, that's not a problem....that's bragging!!!!
Paul
_________________ What goes around, comes around. |
||
| Top | |
||
| syko4d |
|
|||
|
ok i just built eeryhing for my eb series 2 and i dont have a 38 pin its empty?
has anyone done this to a eb series 2 what pin did you use? and yes its the 4 speed btr i have pin 57 but no 38?
_________________ now playing with a v8 to hahaha |
|||
| Top | |
|||
| Paulmac |
|
||
|
syko4d,
PM 'BenJ', 2 posts above and click on the pm button. Ben's becoming the EB guru on these things and will probably help you. Paul
_________________ What goes around, comes around. |
||
| Top | |
||
| syko4d |
|
|||
|
yeah i did that thanx mate
_________________ now playing with a v8 to hahaha |
|||
| Top | |
|||
| AU99 |
|
|||
|
{USERNAME} wrote: neds fantastic simple diagram of the shift kit even an old f@rt like me (57) can understand can you tell me if the au has the same numberd pins as the e series ecu===job well done===
wire up same as EF, hope that helps
_________________ 2003 BA Falcon Egas Taxi Pack - XR Replica |
|||
| Top | |
|||
| Paulmac |
|
||
|
The pin numbers used for the EB-ED shift kit seem to be hard to find in this long thread, so I'll post this up to make them easier to find:
The 18 ohm resistor wire goes to pin 57 The 5.6 ohm resistor wire goes to pin 38 You can use a 20ohm resistor instead of the 18ohm to achieve a less harsh but still quick, change. Cheers, Paul
_________________ What goes around, comes around. |
||
| Top | |
||
| BenJ |
|
||
|
Small correction there Sir
The second resistor, is not 5.6ohms (which is for EF six only) it is 1.0ohm for the others, six cylinder only. V8s and EAs with separate TCM are different again. BenJ
_________________ {DESCRIPTION} - Current Ride |
||
| Top | |
||
| Paulmac |
|
||
|
Well done Ben, 16 mins for the correction! I win the bet by 4 minutes, I knew you'd pick it up in under 20mins!
I did mean to type the one ohm but I was laughing so much I screwed up and just as I was going to try to edit it your post caught me out. So now I'm laughing even more... you see there were two dudes fitting a BBM and...oh well wrong thread, another time perhaps? Cheers, Paul
_________________ What goes around, comes around. |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 22 guests |
