|
| prydey |
|
|||
|
does the jaycar speedo corrector alter the odometer as well or just the speedo. i had never really given it much thought and assumed that the odo ran off the speedo. a guy at work reckons he was told it only changes the speedo and the odo keeps clocking up the km's like it used to.
can anyone confirm this. also to those that have used them, where did you mount it/install it, and what did you use for power (pos/neg).
_________________ eb v8: low loud and fast. just how a v8 should be. i guess the big question is, is it fast enough... |
|||
| Top | |
|||
| alpha141 |
|
|||
|
I had one in my old NC fairlane. Does both speedo and odom. I installed it at the back of the dash behind trip computer and aircon ducting. I powered it off the instriment cluster ignition switched supply (not the constant supply).
hope that helps |
|||
| Top | |
|||
| prydey |
|
|||
|
thanks mate. thats exactly what i wanted to know. if it wasn't going to change the odo as well i wasn't going to bother with it.
_________________ eb v8: low loud and fast. just how a v8 should be. i guess the big question is, is it fast enough... |
|||
| Top | |
|||
| NUTZEF |
|
||
|
does it correct the stift point in your auto or just the speedo/odometer thats somthing to think about
_________________ WOLF V500, t66(ar70 compressor), rochester 550cc injectors, borgg 265l fuel pump, 48mm turbosmart gate, turbosmart plumb back bov, 600x300x100 cooler, 3 inch zorst , 3.45 lsd, xr6 head, wade 1604 cam, adjustable cam gear, K&N pod filter, on 10psi and manual convertion exedy button clutch. 285.6rwkw |
||
| Top | |
||
| prydey |
|
|||
|
shift points don't seem to be affected. already put black (23 tooth) drive gear in box and shift points stayed same. its an eb1 if athat makes any difference. either way if the shift points are affected i can jst put the original speedo gear back in and adjust using the jaycar corrector. as far as i know the corrector has no bearing on the shift pattern.
_________________ eb v8: low loud and fast. just how a v8 should be. i guess the big question is, is it fast enough... |
|||
| Top | |
|||
| Disco Frank |
|
|||
|
is the corector accurate for both spedo and odo?
or it is accurate for spedo, out for odo accurate odo out for speed or do u guys set a "happy" point inbetween?
_________________ RIP SCOTT |
|||
| Top | |
|||
| prydey |
|
|||
|
i'm assuming the odo runs off the speedo so if i 'correct' the speedo the odo will also be 'corrected'
_________________ eb v8: low loud and fast. just how a v8 should be. i guess the big question is, is it fast enough... |
|||
| Top | |
|||
| alpha141 |
|
|||
|
yep thats right, odo runs off speedo, so correct the speedo and the odo runs correctly too. I dont know about auto shift points as I only installed a speedo corrector after converting me old lane to a manual. But it depends on where you tap into the speedo signal. you can tap into it before it branches off to the EEC and dash then both will see the correct speed, altho this wasnt the way I did it. also a tip for setting it up, I found the default 0.5sec update time worked best for me if you try for a quicker time the speed signal jumps up and down a fair bit
|
|||
| Top | |
|||
| prydey |
|
|||
|
i didn't notice any sort of 'update time' adjustment on mine. jst adjustment for % speedo is out.
_________________ eb v8: low loud and fast. just how a v8 should be. i guess the big question is, is it fast enough... |
|||
| Top | |
|||
| alpha141 |
|
|||
|
I had the mk2 version of the kit and it was an option when setting up only. the default works well ne ways.
|
|||
| Top | |
|||
| prydey |
|
|||
|
mine is also the mk2 jaycar version. went to install it today only to find it says to have it on some 'lk2' setting for +5v or something and i don't know how to make sure if the jumpers/links are accross the right terminals. can u offer any advice in this regard.
_________________ eb v8: low loud and fast. just how a v8 should be. i guess the big question is, is it fast enough... |
|||
| Top | |
|||
| falcon_3512003 |
|
|||
|
i cant even get my speedo to work hooked it up rite to and its put the car into limp mode but yet the small led flashes like the instructions say anyone know what could be rong
_________________ now have a series 1 au starting the mods slowly |
|||
| Top | |
|||
| alpha141 |
|
|||
|
I basicly just followed the install guide, which sadly I no longer have... the link I think your talking about has three options for the type of input?? I dont think I had it set for a 5v input but I had it set for auto detect of input type. If you can give me more info as to the options would help, as I said I havnt got the booklet ne more
|
|||
| Top | |
|||
| prydey |
|
|||
|
to update i have installed mine and all is working as it should. ended up with links on lk2 and lk4.
_________________ eb v8: low loud and fast. just how a v8 should be. i guess the big question is, is it fast enough... |
|||
| Top | |
|||
| ringastinga |
|
||
|
ok i know im digging up and old topic but it answered most my questions but i have a few more:
my car is eb wagon, im installing 3.9lsd and 18inch wheels 1. has any1 used this http://www.jaycar.com.au/productView.as ... &SUBCATID= ? 2. any good? 3. how hard? 4. should i use a black gear to get my speedo reading a little closer first?? |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 140 guests |
