|
| clampy |
|
||
|
power steering pump as a leak is there a seal. can i replace it or just get a new pump??
_________________ EL Futura 5 speed factory:PH47FL goneeeee |
||
| Top | |
||
| cp1pgo |
|
|||
|
if i were you i would just get a new pump
_________________ 1995 EF Ford Falcon Fairmont |
|||
| Top | |
|||
| tiny56 |
|
||
|
you can get a seal kit off ebay for like $10 - piss easy to fit
and if you got a el el go to ford and get au high pressure hose fitting cut your old one off and swap it and you wont have leak at that fitting |
||
| Top | |
||
| ToranaGuy |
|
|||
|
tiny56 wrote: you can get a seal kit off ebay for like $10 - piss easy to fit and if you got a el el go to ford and get au high pressure hose fitting cut your old one off and swap it and you wont have leak at that fitting It's easy to fit if you have the pulley remover tool to remove the pulley. They are not too expensive to pick up at Bursons. I've got one, makes it so easy to re-seal the pump. Cheers ToranaGuy
_________________ I am the ToranaGuy!|74 Lh Torana Turbo|78 Hz PanelVan|86 Mighty Boy Ute|93 EB2 Ghia,GT Mockup,5spd,LPGI,Full Leather|2 x EB Xr8 5spd's|FS [VIC]: Wrecking - Eb XR8 - Parts available |Build Thread|Ebay Items - Ford Parts| |
|||
| Top | |
|||
| jaysway |
|
|||
|
ToranaGuy wrote: tiny56 wrote: you can get a seal kit off ebay for like $10 - piss easy to fit and if you got a el el go to ford and get au high pressure hose fitting cut your old one off and swap it and you wont have leak at that fitting It's easy to fit if you have the pulley remover tool to remove the pulley. They are not too expensive to pick up at Bursons. I've got one, makes it so easy to re-seal the pump. Cheers ToranaGuy how much did you pay for it mate? |
|||
| Top | |
|||
| ToranaGuy |
|
|||
|
I think it was about $65 bucks, universal kit that does most common power steer pump pulleys from the 60's to the late 90's.
Cheers ToranaGuy
_________________ I am the ToranaGuy!|74 Lh Torana Turbo|78 Hz PanelVan|86 Mighty Boy Ute|93 EB2 Ghia,GT Mockup,5spd,LPGI,Full Leather|2 x EB Xr8 5spd's|FS [VIC]: Wrecking - Eb XR8 - Parts available |Build Thread|Ebay Items - Ford Parts| |
|||
| Top | |
|||
| XRfairmont67 |
|
|||
|
if the pump is just leaking behind the pulley where the cast iron pump part meets the pressed steel housing u can buy a seal kit from your local parts place for around $20 and just replace that large o'ring , that will stop any leaks from the front, if u buy the pulley tool i guess u can replace all the seals inside aswell.
_________________ http://www.yamahait.com.au/forum/ Last edited by XRfairmont67 on Sat Oct 17, 2009 3:55 pm, edited 1 time in total. |
|||
| Top | |
|||
| cjh |
|
|||
|
How are you goin to compress the spring behind the plate inside the pump??????
_________________ http://youtu.be/jJTh9F3Vgg0 |
|||
| Top | |
|||
| XRfairmont67 |
|
|||
|
is that question directed at me cjh?
ive only pulled a few pumps apart and replaced the 4 rubber seals that normally leak. the large main o'ring at the front, the 2 screw o'rings on the back and the rubber on the valve that the high pressure line screws into. i have never had the cast iron pump apart. wouldnt be hard to make up a tool to compress the cap and spring to remove the circlip though, spring pressure isnt much, u can press the cap in a couple of mm with your thumbs. not hard for me anyway. i have only had problems with leaks, not problems with pressure. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 61 guests |
