|
| qikgs |
|
||
|
Hi there,
Im new to this forum. I have recently purchased a 1998 XH2 S-pack V8 ute with the factory 5.0 EFI windsor and 4 speed auto. The problem is when you press the accelerator more than about a quarter the engine stumbles badly like its running out of fuel or timing is way retarded. It starts and idles well. Have replaced spark plugs, airfilter so far. I am new to injected V8's Does any one know how many of these utes were made? i gather they are reasonably rare. Any help much appreciated |
||
| Top | |
||
| sooty72 |
|
|||
|
Start with the basics. I'd check the timing first, if that is OK, the start looking at everything else. How old are the plugs/leads/dist cap & rotor/air filter/fuel filter? If you are not sure, replace them all. The injectors may need a clean/service. Worst case, replace them. Good luck.
_________________ Yes, I own a Ute. No, I won't help you move! |
|||
| Top | |
|||
| qikgs |
|
||
|
Plug leads look original, dizzy cap looks o.k. air filter done. Ute has 250K on clock
|
||
| Top | |
||
| GASSA |
|
||
|
Mate
Check the crank angle sensor a common fault Gassa
_________________ When the clutch drops the bull s**t stops!!!!! |
||
| Top | |
||
| snap0964 |
|
|||
|
^^^^ Don't bother looking for it, as the XH V8's run a dizzy just like the EF/EL V8's.
{USERNAME} wrote: Does any one know how many of these utes were made? i gather they are reasonably rare. There seem to be less of them around than even the XHII XR8's.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| Sturmovik |
|
|||
|
250k kms is a bit excessive on a set of leads, get a new set.
If the leads are original so would the dizzy cap and rotor, and are probably in worse shape than the leads. Then do the fuel filter. And give the Maf sensor a clean.
_________________ 1993 ED XR6 5speed Polynesian Green. Project car. |
|||
| Top | |
|||
| fairmont54 |
|
||
|
get a can of carbycleaner and spray it around the inlet manifold gasket and vaccum hoses if the engine responds to it that tels you that it is sucking air through there and it will be leaning out. got access to a scan tool?
|
||
| Top | |
||
| qikgs |
|
||
|
No access to scan tool unfortunately.
|
||
| Top | |
||
| fairmont54 |
|
||
|
most places arent to dear to scan somthing up plus they think they might get extra work out of it, we charge 88$ for a scan so its not really that dear
|
||
| Top | |
||
| V8 Ghia Mike |
|
||
|
+1 fuel filter.
Ford diagnosed exactly the same problem with my car as a faulty MAF (of course they would...) but it turned out to be the fuel filter. The car was just struggling for fuel. Also replace the little adaptor between the fuel pump outlet and the hard fuel line on the pump bracket. Mine was leaking, spraying fuel back into the tank and reducing pressure in the line. Mike
_________________ EF Ghia 5.0 - XR8 in a tuxedo....classy, low and loud |
||
| Top | |
||
| XH5LWEPN |
|
|||
|
Clean the MAF hotwires.
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| qikgs |
|
||
|
Ive bought a new fuel filter and will fit it this weekend, How do I go about cleaning the MAF hotwires?
Cheers |
||
| Top | |
||
| XH5LWEPN |
|
|||
|
Un-plug MAF sensor.
Remove rubber intake elbow. Remove air-box lid with MAF on it. Using a tamperproof bit, carefully remove the sensor from the side of the MAF. You'll then see the two hotwires. Carefully spray them with some electrical contact cleaner or brake cleaner untill they are visibly clean. Re-assemble ensuring intake elbow is tight and MAF is plugged back in.
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| qikgs |
|
||
|
Cleaned MAF sensor and replaced fuel filter. Now runs like it should!
Thanks for the help. |
||
| Top | |
||
| XH5LWEPN |
|
|||
|
Good work mate, thats what these forums are for.
_________________ STREETBUILT RACING |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 35 guests |
