|
| GT-01 |
|
|||
|
hey, i have a BA MkII turbo ute and i just purchased a 3 gauge pod, i was thinning of getting a boost gauge and oil pressure gauge but i m unsure on what other gauge i should get? which wouldn't be a waste, any suggestions??? thanks guys
|
|||
| Top | |
|||
| Mr.Kiss |
|
|||
|
oil Temp - when flogging the turbos they have been known to heat up a bit, dont wanna go burning your oil too much!
there's no real point in getten an Air Fuel Ratio guage unless you have a wide band O2 sensor..
_________________ My Cars |
|||
| Top | |
|||
| GT-01 |
|
|||
|
thanks man, which one do you reckon is more important oil pressure and oil temperature? any other gauges u can think of that would b handy to have?
|
|||
| Top | |
|||
| Mr.Kiss |
|
|||
|
you have a turbo yeah? BOOOOOOOST guage! always fun to watch! just not when it over boosts ( , but then thats why you get it!
I only have 2, boost & oil pressure, but if i was to get a third it'd be oil temp..
_________________ My Cars |
|||
| Top | |
|||
| GT-01 |
|
|||
|
i might get boost, oil pressure and oil temp, thanks for ur help man, btw i love ur car, where u get all ur work done, in mel???
|
|||
| Top | |
|||
| Mr.Kiss |
|
|||
|
Well all the work done to my car wasnt at the one place..
Valve springs got done at Nizpro Auto was done at Bayswater Automatics Front half of the exhaust (turbo to end of cat converter) was done by Ace Exhaust's in Ringwood. I did it from the cat back. I installed the Process West intercooler and under battery pipe, trans oil cooler, and guages. the rest was installed by Danny (AKA Headsex on fordxr6turbo.com) he did; installed 12psi actuator and ported the wastegate seimans 60lb injectors in-tank walbro fuel pump Headsex also tuned it. hopefully getten a retune very soon because the dump pipe and 3.5" cat only just got installed, so hoping for around 320rwkw!
_________________ My Cars |
|||
| Top | |
|||
| GT-01 |
|
|||
|
awsum figure man, what about a water temperature gauge? waste u reckon or???
|
|||
| Top | |
|||
| Mr.Kiss |
|
|||
|
{USERNAME} wrote: awsum figure man, what about a water temperature gauge? waste u reckon or??? haha ya should've seen my reaction when it didnt pull 300rwkw at the Ford Mods dyno day last year, wasnt happy! I just wanna get over that magic 300rwkw mark then i'll stop modding! I dont see the point, you already have a water temp guage on your dash cluster, in my opinion it's kinda like getten a monster tacho when you already have a perfectly fine tacho in your dash.... But thats just my opinion anyway..
_________________ My Cars |
|||
| Top | |
|||
| xcabbi |
|
||
|
Personally if your standard gauge is working like it is supposed to then I rate them almost in the same league as after-market fuel level gauges. Pure wank factor.
|
||
| Top | |
||
| GT-01 |
|
|||
|
yeah i want over 300rwkw then would b happy, well i say that now but when i hav 300rwkw i will want more lol, yeah i reckon i will just get boost, oil temperature and oil pressure. should look awsum sitting up on the dash
|
|||
| Top | |
|||
| data_mine |
|
|||
|
{USERNAME} wrote: thanks man, which one do you reckon is more important oil pressure and oil temperature? any other gauges u can think of that would b handy to have? I'd have (and do) oil temp and oil pressure.* The only other option I'd consider is water temp (the factory gauge in the cluster is rather insensitive) *FWIW FPV put a oil pressure and boost gauge in the F6's. GT's get oil temp and oil pressure
_________________ 1998 DL LTD in Sparkling Burgundy, daily, 302W, stereo, slow |
|||
| Top | |
|||
| GT-01 |
|
|||
|
thanks data_mine, looks like boost,oil pressure and oil temperature are the go, thanks guys great help
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 35 guests |
