|
| jughead302 |
|
||
Age: 34 Posts: 326 Joined: 3rd Nov 2009 Ride: AUII XR8 Pursuit & EF XR6 Location: Albion Park |
Im nearly all done with my rebuild on my ute, got a new auxilary drive shaft fitted and shes all sweet. Would it be advisable to change the dizzy?? Ive checked the dizzy for teeth damage from the busted aux shaft and theres not a scratch on the dizzy drive. Anything else I should check in regards to the dizzy drive so I dont have this issue again???
Cheers, Justin
_________________ - 1994 EF XR6, Auto, EL XR wheels. Clean and close to original ( Missus' Kiddie Chariot ) |
||
| Top | |
||
| jughead302 |
|
||
Age: 34 Posts: 326 Joined: 3rd Nov 2009 Ride: AUII XR8 Pursuit & EF XR6 Location: Albion Park |
Nah the shaft I got is from an EF Fairmont that runs the coil pack unit. The dizzy thats in my car doesnt appear to be very old at all, looks as though there was issues before I bought the car and they just stuck a new dizzy in with some of the teeth missing off the Aux. Way I worked the out is because there was very minimal metal to the state the shaft was in.
Will post a photo of the shaft tomorow.
_________________ - 1994 EF XR6, Auto, EL XR wheels. Clean and close to original ( Missus' Kiddie Chariot ) |
||
| Top | |
||
| jughead302 |
|
||
Age: 34 Posts: 326 Joined: 3rd Nov 2009 Ride: AUII XR8 Pursuit & EF XR6 Location: Albion Park |
Yeah very very weird. A bloke I work with used to work at Ford when these XH Tickys were being built and they were very common for stripping the shaft and leaving the dizzy untouched. There was a recall before delivery that required replacement of the shaft as there was ex amount with the "soft" aux drives. Obviously not all of them were fixed. So back to my topic, the dizzy I have should be acceptable??
_________________ - 1994 EF XR6, Auto, EL XR wheels. Clean and close to original ( Missus' Kiddie Chariot ) |
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
jughead302 wrote: Nah the shaft I got is from an EF Fairmont that runs the coil pack unit. The dizzy thats in my car doesnt appear to be very old at all, looks as though there was issues before I bought the car and they just stuck a new dizzy in with some of the teeth missing off the Aux. Way I worked the out is because there was very minimal metal to the state the shaft was in. Will post a photo of the shaft tomorow. You should be able to get the gear off the bottom of the sync sensor from the EF. That would be the ideal way to do it. |
||
| Top | |
||
| jughead302 |
|
||
Age: 34 Posts: 326 Joined: 3rd Nov 2009 Ride: AUII XR8 Pursuit & EF XR6 Location: Albion Park |
So its just as easy as punching out the pin and swapping out drives?? Use a new pin when I do this?? Sounds like the way to go.
_________________ - 1994 EF XR6, Auto, EL XR wheels. Clean and close to original ( Missus' Kiddie Chariot ) |
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
should be able to use the old pin.
|
||
| Top | |
||
| jughead302 |
|
||
Age: 34 Posts: 326 Joined: 3rd Nov 2009 Ride: AUII XR8 Pursuit & EF XR6 Location: Albion Park |
Even better, just swap and go! Thats the only thing that had me worried, not really keen on another stripped drive.
_________________ - 1994 EF XR6, Auto, EL XR wheels. Clean and close to original ( Missus' Kiddie Chariot ) |
||
| Top | |
||
| tickford_6 |
|
||
Posts: 6449 Joined: 11th Nov 2004 |
what oil do you use?
|
||
| Top | |
||
| jughead302 |
|
||
Age: 34 Posts: 326 Joined: 3rd Nov 2009 Ride: AUII XR8 Pursuit & EF XR6 Location: Albion Park |
Ive always used Penrite oils throughout all my cars but I had only owned the ute 1 day before it stopped.
_________________ - 1994 EF XR6, Auto, EL XR wheels. Clean and close to original ( Missus' Kiddie Chariot ) |
||
| Top | |
||
| snap0964 |
|
|||
|
Check the sideplay in your dizzy (the vanes going through the hall pickup), and replace the bush if needed - bushes were around $9 from fraud when I bought them (around 7 mths ago). If you do replace the bush, check the end float with a feeler gauge, and set up the new as same - this is achieved by the location of the bush, so carefully tap in, temp install the shaft and drivegear, and check measure til you get what you want.
Other thing is, if you remove the TFI, make sure you have some heatsink paste - good if you know someone from IT, as it is a bit expensive.
_________________ 96 XH Longreach 'S': LPG, Alarm, 3.23:1 LSD, Cruise, Trip Comp, ABS, Power Windows, Mid Series Dome Lt, Climate Ctrl |
|||
| Top | |
|||
| jughead302 |
|
||
Age: 34 Posts: 326 Joined: 3rd Nov 2009 Ride: AUII XR8 Pursuit & EF XR6 Location: Albion Park |
Finally got the ute up and running with minimal issues. Just wondering how to set the base timing so I can get the best out of the timing. Also I have a little bit of timing chain slap, would this just be a sticky tensioner??
_________________ - 1994 EF XR6, Auto, EL XR wheels. Clean and close to original ( Missus' Kiddie Chariot ) |
||
| Top | |
||
| jughead302 |
|
||
Age: 34 Posts: 326 Joined: 3rd Nov 2009 Ride: AUII XR8 Pursuit & EF XR6 Location: Albion Park |
Yeah I screwed the plug in and then stuck a screwdriver in and I heard it undo itself and unlock but the slide is feeling a bit stiff to move in and out, maybe needs more lubrication. Other than that she runs like a clock!
_________________ - 1994 EF XR6, Auto, EL XR wheels. Clean and close to original ( Missus' Kiddie Chariot ) |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 115 guests |
