|
| FordEb'L'unatic |
|
||
|
Apparently my two rears are ''severly'' buckled & front left slightly..ive just chuckd a 3.45 into my eb ..Didnt change the sway bar (if u needed to. it was a pain) but im just wondering would it be the axels in the diff, or the actual rims buckled because i can hear the tires on the road sorta making that wobble noise..it aint fully bad like they gunna pop off and ima go skating without back rims lol
but what you think? |
||
| Top | |
||
| svo_matt |
|
|||
|
who said the rims are buckled did you just assume they are or did the bloke at the tyre shop say they were (checked on a balancer)
_________________ ..My fake plant died because I forgot to pretend to water it.. |
|||
| Top | |
|||
| FordEb'L'unatic |
|
||
|
bob jane on wheel alignment and tire fitting...
|
||
| Top | |
||
| Froudey |
|
||
|
{USERNAME} wrote: bob jane on wheel alignment and tire fitting... I suggest getting another set of rears (like borrow some standards or something) and go for a drive, if it seems fine then rims are rooted, but if it still seems how ya going then axles might rooted or something
_________________ R.I.P Tobias my son. |
||
| Top | |
||
| FordEb'L'unatic |
|
||
|
308 standard single spinner diff axel & 3.45 lsd spline the same & compatible?..was thinkin of chuckin in the other axels
|
||
| Top | |
||
| Steady ED |
|
|||
|
do you have some reason to not trust this joints word?
because when they have a wheel/tyre on a balancing machine, it's really hard to mistake a bent axle for a buckled wheel 
_________________ ED XR8 Sprint - S-Trim, V500, 249rwkw |
|||
| Top | |
|||
| FordEb'L'unatic |
|
||
|
yes well u got a point there..but they are bob jane they do like to try f**k people over :p but yeh didnt think of that haha..was mainly concerned because i just switched over a 3.45 and didnt know about the axels since it was a diff that used to like getting thrashed a bit..but yeh thanks for opening my dumbass mind and relising that..i feel like a tool haha..and yeh i ask people twice not just one person aswell
|
||
| Top | |
||
| eb_dean |
|
||
|
{USERNAME} wrote: yes well u got a point there..but they are bob jane they do like to try f**k people over :p but yeh didnt think of that haha..was mainly concerned because i just switched over a 3.45 and didnt know about the axels since it was a diff that used to like getting thrashed a bit..but yeh thanks for opening my dumbass mind and relising that..i feel like a tool haha..and yeh i ask people twice not just one person aswell Why would you say the like to f**k people over ?? Have you been f**k over before by them ?
_________________ 1993 EB XR6 Factory 5spd-2.5" exhaust w/ dump pipe-Genuine BA XR8 18" wheels-K&N filter-Momo Steering Wheel-Pioneer Head Unit-Sony 12" Sub-Pioneer 600w MonoBlock 4ch Amp- Xplod 6x9's-Superlowed |
||
| Top | |
||
| lukey1990 |
|
||
|
My experience with Bob Jane's has been very good, I bought a set of 18" alloys for my first car from them, and I've also had other cars there too.
And they even arranged to have a wheel nut drilled out for me too, which I guess is their job, but I called them up in the morning and had it removed by early afternoon after making the booking.
_________________
|
||
| Top | |
||
| ReGiE |
|
|||
|
i got some new tyres a few months ago from them, all good except they forgot to tighten the rear nuts..needless to say i went back and gave them some words
_________________ Gooooone - Eb2 Coon - 143RWKW |
|||
| Top | |
|||
| FordEb'L'unatic |
|
||
|
{USERNAME} wrote: {USERNAME} wrote: yes well u got a point there..but they are bob jane they do like to try f**k people over :p but yeh didnt think of that haha..was mainly concerned because i just switched over a 3.45 and didnt know about the axels since it was a diff that used to like getting thrashed a bit..but yeh thanks for opening my dumbass mind and relising that..i feel like a tool haha..and yeh i ask people twice not just one person aswell Why would you say the like to f**k people over ?? Have you been f**k over before by them ? yes...with wheel balancing...so i have reason 
|
||
| Top | |
||
| eb_dean |
|
||
|
{USERNAME} wrote: {USERNAME} wrote: {USERNAME} wrote: yes well u got a point there..but they are bob jane they do like to try f**k people over :p but yeh didnt think of that haha..was mainly concerned because i just switched over a 3.45 and didnt know about the axels since it was a diff that used to like getting thrashed a bit..but yeh thanks for opening my dumbass mind and relising that..i feel like a tool haha..and yeh i ask people twice not just one person aswell Why would you say the like to f**k people over ?? Have you been f**k over before by them ? yes...with wheel balancing...so i have reason but your first post you say "apparently they are buckled" like you know better than they do. they aren't there to pat wombats, they know wat there talking about. I'm mechanic. you can instantley see a buckled rim. there doing there job and your obvisously not hearing what you want so you say your gettin f**k over.
_________________ 1993 EB XR6 Factory 5spd-2.5" exhaust w/ dump pipe-Genuine BA XR8 18" wheels-K&N filter-Momo Steering Wheel-Pioneer Head Unit-Sony 12" Sub-Pioneer 600w MonoBlock 4ch Amp- Xplod 6x9's-Superlowed |
||
| Top | |
||
| Esteven8 |
|
|||
|
Could also be your wheel bearings causing the 'Wobble' noise. Just one more thing to check.
 (edit) Might pay to check the bearings anyway, if you've been driving around on buckled rims or bent axles (whatever the case my be) the vibration won't be doing the bearings any favors.
_________________ {USERNAME} wrote: Cheap pads squeal like cheap hookers, and you can take that to the bank. {DESCRIPTION} {DESCRIPTION} |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 23 guests |
