|
| Marmo aka GRNGOB |
|
|||
|
hey guys i saw a car a while back it was an ed turbo with an ed inlet plenum and it had two sets of injectors just wondering what ecu/how it would be set up as it woudl have to be a hell of a lot cheaper then getting new higher rated injectors and fuel pumps and it looked sik too i will post up pic when i get home.. thanks
_________________ Spooling soon... |
|||
| Top | |
|||
| 4.9 EF Futura |
|
|||
|
Marmo, was it a full set of injectors or plumbed into the plenum? Were they for fuel or water/methanol injection maybe?
Can be controlled by most aftermarket ECUs... they can run a different fuel map for the second set of injectors.. you could prolly rig it up to have EEC control the standard injectors and a wolf/similar to control the second set... but best to go aftermarket imo. Dunno if it'd be much cheaper... you need a fuel rail etc and by the sounds of it a fair bit of cutom work... cant escape the need for a good fuel pump either... Have also seen liquid LPG systems with a second fuel rail/injector set...
_________________ I promise..... I will never die. |
|||
| Top | |
|||
| EDXR8 |
|
|||
|
Yeah I have seen a few done that way. Generally they run a 2nd fuel only computer to bring in the 2nd set of injectors under boost. IMO its easier and probably around the same cost to run a single set of injectors (36-42lb) rather than going to the hassel of rigging a 2nd rail in.
|
|||
| Top | |
|||
| Marmo aka GRNGOB |
|
|||
|
ok kewl thanks guys btw i couldnt find the pic must have lost it when i reformated
_________________ Spooling soon... |
|||
| Top | |
|||
| Marmo aka GRNGOB |
|
|||
|
how much rwkw can the std injecters handle?
also how much is a set of 42lp/h ones and how many rwkw they good for?
_________________ Spooling soon... |
|||
| Top | |
|||
| EDXR8 |
|
|||
|
Stock injectors are really only good for around 175rwkw with stock pressure. Increasing the fuel pressure allows some people to squeeze around 200rwkw out of them. 42lb injectors are fine until well over 300rwkw on a 6cyl. You can get Ford motorsport 42lb injectors from the US for $4-500 landed.
|
|||
| Top | |
|||
| Marmo aka GRNGOB |
|
|||
|
EDXR8 wrote: Stock injectors are really only good for around 175rwkw with stock pressure. Increasing the fuel pressure allows some people to squeeze around 200rwkw out of them. 42lb injectors are fine until well over 300rwkw on a 6cyl. You can get Ford motorsport 42lb injectors from the US for $4-500 landed.
awsome i was thinking of like 1k for injectors, i feel the turbo kit coming on sooner, my aim in the end is around 250-300rwkw what would your reckonmend for ecu? also how much would the fuel pump be, lieka run down of the whole fuel system
_________________ Spooling soon... |
|||
| Top | |
|||
| EDXR8 |
|
|||
|
Run a Walbro in-tank 255l/hr pump, plenty of flow for that sort of power. MrLandau has them for $165 (http://www.fordmods.com/phpBB2/viewtopic.php?t=3875). For the engine management side of things I would look at the EMS range, the stinger is a decent unit which will probably end up costing around $1600 installed and tuned or you can look at the 8860 with more tuning resolution and features for around $2k
|
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 15 guests |
