|
| gumpmadas |
|
||
|
any one had troble getting cruise to work. been through all tests on this site and only thing that does not check out is speed circuit oooo.o ohms pins 10 & 3 and speed allert is around 10kms out does that affect it can any one point me in right direction. dec 94 ef fairmont.
|
||
| Top | |
||
| Krytox |
|
|||
|
Cruise only works above 40kph.
Check your brake lights first, if they're on the cruise is disabled. Then short out the brake pressure switch on the master cylinder, and give it another go. Also check the blanking short (if the cars auto) this will be hanging behind the fuse-box in the cabin and will be covered with foam. you may have to fish for it.
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| gumpmadas |
|
||
|
testing at 60 kms ,brake lights off,jumped pressure sw. i noticed there is a clunk noise under bonnet
when you have cruise on and when you hit each of the right hand buttons i assume its the cable solenoid in cruise module and it does not make the noise when fethering the brake as traveling at 60km so i assume the brake circuit is ok. jumping the pressure sw also stopped this noise. i tried to power the cc motor but it only turns very slightly in both directions? i will go fishing for jump wire it is auto. |
||
| Top | |
||
| Krytox |
|
|||
|
you've checked the throttle cable right?
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| gumpmadas |
|
||
|
whats to check apart from obvious ?
|
||
| Top | |
||
| Krytox |
|
|||
|
it wraps around a nylon guide inside the motor (stepper) case, possible derailment ¿
_________________ Carefree, we may not be number one, but we're up there. |
|||
| Top | |
|||
| gumpmadas |
|
||
|
cable all good ,not binding or derailed , had unit in bits all like new as if never worked. car new to us. found small two pin connector under dash with jumper wire that one looks good.
think will try a mates unit since this one is on lounge floor. all brake lights work very well. Last edited by gumpmadas on Mon Apr 18, 2011 7:07 pm, edited 1 time in total. |
||
| Top | |
||
| arm79 |
|
|||
|
Any of your brake lights dead?
If one or both of the main globes are popped, the cruise wont turn on. |
|||
| Top | |
|||
| gumpmadas |
|
||
|
put new unit in works great. the motor had @#it itself.
|
||
| Top | |
||
| a96ute |
|
||
|
gumpmadas I'm also having issues with my CC also & I'm interested to know what this "small two pin connector" with "jumper wire" is & does.
|
||
| Top | |
||
| arm79 |
|
|||
|
If its the one I'm thinking of, it's the plug for the clutch pedal cancel switch. Taped into the loom on the top right of the firewall.
It needs to have a joiner between the 2 for auto cars or the cruise control doesn't work. |
|||
| Top | |
|||
| a96ute |
|
||
|
I'm confused - all I can see is a white square one with 2 spade connecters at right angles to each other - is that the one ??????
|
||
| Top | |
||
| Shen Long |
|
|||
Age: 49 Posts: 391 Joined: 22nd Aug 2008 Ride: 2002 AUII Fairlane Sportsman V8 Location: Roxby Downs |
i had a simular issue with my cruise control functionality.
Funnily enough it was a stupid clip that does who knows what which clips into the cruise control cable. If you look at your cruise control cable near the throttle body just above the rocker cover you will notice that the cable has an 8mm bolt that bolts into the rocker cover for support/functionality etc. Anyhow in that vicinity you will notice that the cable has "teeth or grooves" for lack of a better word & a clip can be put there. Well you may need to remove the clip & adjust it so that the cable is longer or shorter. I have 3 grooves poking out of the actual cable (i hope that makes sense) Well anyways long story short, it fixed my problem  I could hear the module trying to engage however it did not want to engage at all until i adjusted the clip. |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 80 guests |
