|
| SWC |
|
||
|
Lot depends on the condition of the box, age, KM, How its been looked after. Also don't forget your diff.
|
||
| Top | |
||
| Fordsrule174 |
|
||
|
im going for a 3.45LSD XR6 borgwarner it should handle it really easily
i dont mind the snort performance eaton supercharger m112 kit that maxes at 250KW would this work with stock rods etc ? should i bother with a AU conversion or would a EF motor suit just fine ? and how would the stock 4spd go with that power ? assuming good well looked after condition ?
_________________ NF Fairlane Ghia, Brand New Leather Interior, Wallnut All Through, 800W RMS JL Audio Sound System, Lowered King Springs And Monroe GT Shocks, Custom BA/GT Air Intake, Holley Highflow, Simmons B45's, Going To Be Supercharged At 9-12psi With Stage 4 Head And Cam With Pacemakers And 3" Exhaust |
||
| Top | |
||
| bry40l |
|
|||
|
If you dont drive it flat out everywhere every day it should be ok for 250kw for a while , shift kits can reduce wear by changing the gears quicker giving less slip so id be doing that
_________________ BF XR6 |
|||
| Top | |
|||
| Fordsrule174 |
|
||
|
would a EF motor handle 250KW or would i need forged pistons and rods etc ?
how would the bottom end handle it to ? i know the EF bottom end isnt as strong as the AU
_________________ NF Fairlane Ghia, Brand New Leather Interior, Wallnut All Through, 800W RMS JL Audio Sound System, Lowered King Springs And Monroe GT Shocks, Custom BA/GT Air Intake, Holley Highflow, Simmons B45's, Going To Be Supercharged At 9-12psi With Stage 4 Head And Cam With Pacemakers And 3" Exhaust |
||
| Top | |
||
| TROYMAN |
|
||
|
Fordsrule174 wrote: would a EF motor handle 250KW or would i need forged pistons and rods etc ? how would the bottom end handle it to ? i know the EF bottom end isnt as strong as the AU actually in a way the ef bottom end is stronger than au, as in the ef rods are shorter and can handle more boost.. there are a couple of ef's that are making over 300rwkw on std bottom ends, i think axeman83 is getting 330+rwkw? on a std ef crank and rods.. the au is a better n/a engine, better balancing, higher compression and a more ridged crank/sump design.. if i was going to build an engine specifically for boost, i would use the au bottom end with aftermarket rods and pistons. but a std au engine can still handle a bit.. look at it this way the ba bottom end(crank and rods) is pretty much the same design as the au.. im getting 265rwkw out of a std au engine putting 12 psi into it, dansedgli is getting 280rwkw from his std au engine at around 15psi?.. it all comes down to the condition of the engine and more importantly its the tune that will give it the reliability.. |
||
| Top | |
||
| krisisdog |
|
|||
|
Search ffs. AU bottom ends arent stronger than ef/el when under boost - rods are weaker.
|
|||
| Top | |
|||
| Fordsrule174 |
|
||
|
TROYMAN wrote: Fordsrule174 wrote: would a EF motor handle 250KW or would i need forged pistons and rods etc ? how would the bottom end handle it to ? i know the EF bottom end isnt as strong as the AU actually in a way the ef bottom end is stronger than au, as in the ef rods are shorter and can handle more boost.. there are a couple of ef's that are making over 300rwkw on std bottom ends, i think axeman83 is getting 330+rwkw? on a std ef crank and rods.. the au is a better n/a engine, better balancing, higher compression and a more ridged crank/sump design.. if i was going to build an engine specifically for boost, i would use the au bottom end with aftermarket rods and pistons. but a std au engine can still handle a bit.. look at it this way the ba bottom end(crank and rods) is pretty much the same design as the au.. im getting 265rwkw out of a std au engine putting 12 psi into it, dansedgli is getting 280rwkw from his std au engine at around 15psi?.. it all comes down to the condition of the engine and more importantly its the tune that will give it the reliability.. thanks for clearing that up troyman  everywere i searched i couldnt get that sorta info
_________________ NF Fairlane Ghia, Brand New Leather Interior, Wallnut All Through, 800W RMS JL Audio Sound System, Lowered King Springs And Monroe GT Shocks, Custom BA/GT Air Intake, Holley Highflow, Simmons B45's, Going To Be Supercharged At 9-12psi With Stage 4 Head And Cam With Pacemakers And 3" Exhaust |
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: Google Adsense [Bot] and 87 guests |
