|
| Damian15447 |
|
||
|
afternoon peoples im damian and my ford is a little rusty
 what would be my best approach to this ? 
|
||
| Top | |
||
| Damian15447 |
|
||
|
it is an ef yes that is behind the drivers side guard were that ball shaped thingo is
|
||
| Top | |
||
| 67RCE |
|
||
|
I'd be car shopping if I was you!
_________________ ILL60 - EF XR8, Sunroof, Ticky Kit, 19x8.5/19x11 TE37's, 347, AFr185's, TFS BoxRcustom converter, Hurst Quarterstick, huge billet cam. |
||
| Top | |
||
| bry40l |
|
|||
|
Fukin hell, strip it and sell the parts and go car shopping, I thought my old ef was bad
_________________ BF XR6 |
|||
| Top | |
|||
| Damian15447 |
|
||
|
i didnt think it was structual since that piece is just tacked in getting another car isnt a good option for me at this point ive only got a part time job
|
||
| Top | |
||
| bry40l |
|
|||
|
If I was you id be rubbing that back with sand paper and at least getting some rust convertor on it if getting another car isnt an option
_________________ BF XR6 |
|||
| Top | |
|||
| phongus |
|
|||
|
{USERNAME} wrote: If I was you id be rubbing that back with sand paper and at least getting some rust convertor on it if getting another car isnt an option Sand paper? f**k that just attack it with a power drill and steel wire brush to remove the chunks of rust, then use a sand flapper wheel thing or similar to sand it down to bare metal. Chuck some of that rust convertor on it and then paint it with some anti-rust paint primer. Hopefully that will slow it down.
_________________ phongus = Post whore 2006 |
|||
| Top | |
|||
| Damian15447 |
|
||
|
ive got a sand blaster ?
 worst comes to worst i can get a mig
|
||
| Top | |
||
| OZBMX |
|
|||
|
Holy f**k I've never seen an ef that bad, has she been in a substantial accident in the past I'm thinking that's been damaged and repaired that area, or been parked in the ocean for a week, seriously though I'd be very tempted to look for a donor with say a blown motor stuffed gearbox, for a 100 or 2 and transfer everything over, if it was just the one chunk I'd be more inclined to give it a go, but the way the whole area seems to be bleeding that rust like that, s**t mate.
I'll admit I haven't worried to much about the rust in my xc, but theres a few reason there, one being mines nearly rustfree in xc terms,  but I'd be very weary about the history of your car in general. eek.
_________________ Signature removed by moderator.signature must not exceed 120x500 pixles |
|||
| Top | |
|||
| hans hartman |
|
||
|
{USERNAME} wrote: ive got a sand blaster ? worst comes to worst i can get a migcover most bits and blast it,after see how much is left solid,cut and repair it.you can get the repair bits from the scrap or wrecker places,plenum was holding leaves or rubbish,remove the plastic covers and look behind it,beware of fire when welding
_________________ R.I.P HANS HARTMAN |
||
| Top | |
||
| Damian15447 |
|
||
|
looks like im going to go with the mig route that piece looks to be just spot welded in so it shouldnt be too hard to drill em out
|
||
| Top | |
||
| Who is online |
|---|
Users browsing this forum: No registered users and 26 guests |
