|
| gotta luv a v8 |
|
|||
|
Hi, I have fitted a GT camshaft out of a EL to a completely new 302 windsor for my AU, after a while I also fitted some bolt on yella terra 1.7 RR's since I have noticed when the motor gets into the higher rev range it gets a bit of a rattle in it, is that normal for roller rockers or should the springs be upgraded, thanks
_________________ Don't force it, use a Bigger hammer |
|||
| Top | |
|||
| xafalcon |
|
||
|
Check your lifter pre-load. It should be around 60 thou. Often those "special" camshafts have a smaller base circle which reduces pre-load, sometimes to the point of it becoming zero. A rattly valve train is the result, and continued operation causes damage.
Also those Yella Terra rockers have occasionally suffered from soft pushrod cups. I had an engine through the workshop with several. There was about 100 thou lash for one of the rockers. The pushrod cup was almost worn away to nothing.
_________________ XA Faimont 351C, AU2 XR8 Manual 5.0, DA LTD 5.0, Mk1 Capri 5.0, 1995 Mustang 5.0, EF2 XR8 Manual, EF2 Fairmont Ghia 5.0, AU3 XR8 Auto, AU2 XR8 Auto, AU2 XR8 Manual Ute, TE Cortina 5.0 Manual, DU LTD 5.0 soon to be manual |
||
| Top | |
||
| gotta luv a v8 |
|
|||
|
Ok Thanks, I will check it and the rockers, a rattling drive train would be a more apt description , the rattling has only been noticable since I fitted the roller rockers, I never noticed any noise when the standard rockers were fitted and that was for a few months. have had the rr's fitted for about 10 months has had the rattle the whole time, you can only notice it when the revs get up but has not got any worse.
_________________ Don't force it, use a Bigger hammer |
|||
| Top | |
|||
| Johnson stroker |
|
|||
|
not to nit pick, but a rattling valve train is what you have.
_________________
|
|||
| Top | |
|||
| gotta luv a v8 |
|
|||
|
{USERNAME} wrote: not to nit pick, but a rattling valve train is what you have. Yep, my mistake I meant valve train.
_________________ Don't force it, use a Bigger hammer |
|||
| Top | |
|||
| EBXR8380 |
|
|||
|
I would add better valve springs.. If the rockers have 1;7 ratio over std
that would cause valve float at higher rpm if valve springs are soft.. Also check clearance with breather baffles on your rocker cover...
_________________ As in ZOOM 126 edition |
|||
| Top | |
|||
| gotta luv a v8 |
|
|||
|
Thanks,I have alloy mustang rocker covers fitted and I had to remove the breather baffle so am pretty sure there is enough clearance to the rockers, when the motor is reving low it sounds sweet it is only when it hits about 4000rpm that it starts sounding tappety, not having had anything to do with springs in the past, what replacement springs should I be looking for thanks
_________________ Don't force it, use a Bigger hammer |
|||
| Top | |
|||
| Matt_jew |
|
||
|
Is it a valve train noise or is it pinging?
Windsors are known to ping in the top end when your up it.
_________________ {USERNAME} wrote: More people paid for a ride in a VT commodore then an AU Falcon so the VT is superior.
Based on that fact my Mum is the best around! |
||
| Top | |
||
| gotta luv a v8 |
|
|||
|
No,its definately not pinging more like every tappet is tapping.
_________________ Don't force it, use a Bigger hammer |
|||
| Top | |
|||
| Who is online |
|---|
Users browsing this forum: No registered users and 17 guests |
