Fordmods Logo

AU1 and AU2 T MAP Sensor issue 

 

Page 1 of 1 [ 12 posts ] 

 
 Post subject: AU1 and AU2 T MAP Sensor issue
Posted: Wed Dec 07, 2011 6:32 pm 
Fordmods Newbie
Offline

Age: 38

Posts: 14

Joined: 7th Dec 2011

Gallery: 1 images

Ride: AU 2 Forte Ex Cop car

Location: Western Victoria Australia
VIC, Australia

Hello I recently installed a second hand motor from the wreckers into my AU2 however it runs ok besides the flat spot splutter however the wreckers had told me au 1 right through to au3 are interchangeable. well now after replacing the fuel pump fuel filter and fuel injectors plus oxy sensor the problem is still there I worked it out to be the t map sensor after i was going to swap the au 2 upper bbm manifold and as i found the wiring is different. What would be my best solution to fix this?
Top
 Profile  
 
 
 Post subject: Re: AU1 and AU2 T MAP Sensor issue
Posted: Wed Dec 07, 2011 6:39 pm 
Commercial Sponsor
Offline
User avatar

Posts: 123

Joined: 27th Sep 2007

Ride: eb-twin turbo

Location: albury/wodonga
VIC, Australia

series 1 map sensors have a another style of plug and the wiring is revered

pin a - pin4 , pin b- pin3 ect

you can use the series 2 map sensors but you will need to use the series 2 plug and reverse the wiring

 

_________________

Snort Snort, we make our own speed!!!!!

Top
 Profile  
 
 
 Post subject: Re: AU1 and AU2 T MAP Sensor issue
Posted: Wed Dec 07, 2011 8:01 pm 
Fordmods Newbie
Offline

Age: 38

Posts: 14

Joined: 7th Dec 2011

Gallery: 1 images

Ride: AU 2 Forte Ex Cop car

Location: Western Victoria Australia
VIC, Australia

Thanks it seems to run fine except for the damm flatspot or when on the highway plant your foot it surges a bit however i will get the wiring off the old motor and chuck that on and swap the upper BBM over as the au1 has 2 screws holding it in where as the au2 has one small bolt holding it on wish the wreckers mentioned this as i did ask them and also stated i knew there were a few small changes to the AU2 wireing
Top
 Profile  
 
 
 Post subject: Re: AU1 and AU2 T MAP Sensor issue
Posted: Wed Dec 07, 2011 8:04 pm 
Fordmods Newbie
Offline

Age: 38

Posts: 14

Joined: 7th Dec 2011

Gallery: 1 images

Ride: AU 2 Forte Ex Cop car

Location: Western Victoria Australia
VIC, Australia

or should i just cut the wire from the old loom for the sensor and just reverse it and swap the upper bbm? just funny how it runs just with this small issue
Top
 Profile  
 
 
 Post subject: Re: AU1 and AU2 T MAP Sensor issue
Posted: Wed Dec 07, 2011 8:30 pm 
Fordmods Newbie
Offline

Age: 38

Posts: 14

Joined: 7th Dec 2011

Gallery: 1 images

Ride: AU 2 Forte Ex Cop car

Location: Western Victoria Australia
VIC, Australia

It isn't as efficient as it should be the motor is in good nic low k just wondering what is the easiest way to go about it?
Top
 Profile  
 
 
 Post subject: Re: AU1 and AU2 T MAP Sensor issue
Posted: Wed Dec 07, 2011 8:32 pm 
Commercial Sponsor
Offline
User avatar

Posts: 123

Joined: 27th Sep 2007

Ride: eb-twin turbo

Location: albury/wodonga
VIC, Australia

if you have the series 2 engine loom and map sensor , simply cut the current plug and reverse the wiring

 

_________________

Snort Snort, we make our own speed!!!!!

Top
 Profile  
 
 
 Post subject: Re: AU1 and AU2 T MAP Sensor issue
Posted: Wed Dec 07, 2011 8:38 pm 
Fordmods Newbie
Offline

Age: 38

Posts: 14

Joined: 7th Dec 2011

Gallery: 1 images

Ride: AU 2 Forte Ex Cop car

Location: Western Victoria Australia
VIC, Australia

Righto that is easy to do and there is no other sensors or wiring that need modification?
Top
 Profile  
 
 
 Post subject: Re: AU1 and AU2 T MAP Sensor issue
Posted: Wed Dec 07, 2011 8:41 pm 
Commercial Sponsor
Offline
User avatar

Posts: 123

Joined: 27th Sep 2007

Ride: eb-twin turbo

Location: albury/wodonga
VIC, Australia

not on the vehicles we have done

 

_________________

Snort Snort, we make our own speed!!!!!

Top
 Profile  
 
 
 Post subject: Re: AU1 and AU2 T MAP Sensor issue
Posted: Fri Dec 09, 2011 2:31 pm 
Fordmods Newbie
Offline

Age: 38

Posts: 14

Joined: 7th Dec 2011

Gallery: 1 images

Ride: AU 2 Forte Ex Cop car

Location: Western Victoria Australia
VIC, Australia

Thanks for the help :)
Top
 Profile  
 
 
 Post subject: Re: AU1 and AU2 T MAP Sensor issue
Posted: Thu Dec 15, 2011 2:06 pm 
Fordmods Newbie
Offline

Age: 38

Posts: 14

Joined: 7th Dec 2011

Gallery: 1 images

Ride: AU 2 Forte Ex Cop car

Location: Western Victoria Australia
VIC, Australia

Did the mods today no she runs like a dream again Cheers
Top
 Profile  
 
Display posts from previous:
Sort by  
 Page 1 of 1  [ 12 posts ] 

Who is online

Users browsing this forum: galapogos01, Google Adsense [Bot] and 102 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

 

 

It is currently Mon Nov 25, 2024 9:44 am All times are UTC + 11 hours

 

 

(c)2014 Total Web Solutions Australia - Australian Web Hosting and Domain Names